Zebra 110Xi4 Guide de l'utilisateur télécharger pdf (Page 56)

Operations

Load Media in Cutter Mode

P1009874-003 Xi4™/RXi4™ User Guide 4/30/13

8. Align the media with the inner media guide (1). Slide in the outer media guide (2) until it

just touches the edge of the media.

9. Tighten the thumb screw (not visible from this angle) that is located on the bottom of the

outer media guide (

1).

1 2 ... 51 52 53 54 55 56 57 58 59 60 61 ... 187 188

User Guide 1
Part Number: P1009874-003 2
Declaration of Conformity 3
Compliance Information 4
Contents 5
About This Document 9
Who Should Use This Document 10
Bubbledot ICG font 11
SETUP/EXIT button 12
CALIBRATE button 12
Introduction 13
Printer Components 14
Control Panel 15
Printer Setup 17
Before You Begin 18
Handling the Printer 19
Select a Site for the Printer 20
I) may damage the 21
Interface 23
Standard or 23
Optional 23
Description 23
O) position 26
Power Cord Specifications 27
Types of Media 29
Ribbon Overview 31
Adhesive Test 32
Ribbon Scratch Test 32
Operations 33
Media Paths 35
Cutter Cutter 36
Rewind Rewind (without 36
Cutter option) 36
Prepare the Media for Loading 37
110Xi4/R110Xi4 600 dpi 38
Fanfold Media 40
Load Media in Tear-Off Mode 42
RIBBON OUT error 43
Load Media in Peel-Off Mode 46
Load Media in Cutter Mode 53
Load Media in Rewind Mode 58
If... Then 65
Pull out the spindle hook 66
Load Ribbon 67
If… Then… 68
1) and under the 69
Remove Used Ribbon 72
Calibrate the Printer 74
SENSOR PROFILE 75
MEDIA AND RIBBON 75
CALIBRATE 75
Upper Media Sensor 76
Lower Media Sensor 79
Toggle Position Adjustment 80
Printhead Pressure Adjustment 81
Setup Mode 84
Exit Setup Mode 85
Default Password Value 86
LIST SETUP 87
LIST NETWORK 88
WARNING REPLACE 95
3. Do you want to continue? 97
To print a sensor profile: 98
LOAD BACKING prompt displays 99
RELOAD ALL displays 99
Action/Explanation 100
Configuration 101
To change the value shown: 103
Language/Parameter 103
Error Condition 107
Feed Label 107
To skip these parameters: 108
IDLE DISPLAY 109
Routine Maintenance 113
Replacing Printer Components 114
Lubrication 114
CLEAN HEAD NOW appears 115
CLEAN HEAD NOW 116
1) counter-clockwise 117
Clean the Sensors 119
Transmissive Media Sensor 120
Media Out Sensor Location 121
Clean the Snap Plate 122
RFID Printers 125
Clean the Cutter 128
Replace the Fuse 129
Troubleshooting 131
Troubleshooting Checklists 132
LCD Error Messages 133
LCD Display/ 134
Printer Condition 134
O) the printer 135
I) the printer 135
Print Quality Problems 139
Note • A vertical drift of 141
Calibration Problems 143
NONE. See 144
Ribbon Problems 145
RFID TAG 146
MEDIA POWER UP and 147
O) and then back on (I) too 148
LANGUAGE 149
SAVE CHANGES in the 149
Printer Diagnostics 151
CANCEL Self Test 152
PAUSE Self Test 153
FEED Self Test 154
Print Quality Description 156
FEED and PAUSE Self Test 157
Sensor Profile 159
Specifications 161
Features 162
Bar Codes 163
General Specifications 164
Print Specifications by Model 165
140Xi4, 170Xi4, and 220Xi4 166
Ribbon Specifications 167
Media Specifications 168
End User License 171
Agreement 171
End User License Agreement 172
Glossary 177
Numerics 181

Commentaires sur ces manuels

Pas de commentaire

Zebra 110Xi4 Guide de l'utilisateur Page 56

Commentaires sur ces manuels

Produits connexes et manuels pour Imprimantes d'étiquettes Zebra 110Xi4