Zebra Stripe Guide de l'utilisateur télécharger pdf (Page 51)

Operations

Load Media in Cutter Mode

6/15/09 S4M User Guide 13290L-004 Rev. A

3. Press the printhead release latch to open the printhead assembly. Lift the printhead until it

latches open.

4. Slide out the media guide.

Caution • The cutter blade is sharp. Do not touch or rub the blade with your fingers.

Feed the media under the dancer assembly (1), through the slot in the transmissive

sensor (

2—standard transmissive sensor shown), under the printhead-open sensor (3),

and through the cutter (

4).

123

1 2 ... 46 47 48 49 50 51 52 53 54 55 56 ... 149 150

User Guide 1
Declaration of Conformity 3
Compliance Information 4
Contents 5
Who Should Use This Document 10
Contacts 11
Bubbledot ICG font 12
POWER ALERT 13
CANCEL FEED 13
About This Document 14
Document Conventions 14
Introduction 15
External View 16
FEED FEED 18
Appearance 19
Control Panel Lights 20
Printer Media Compartment 21
Printer Language Modes 22
Printer Setup 23
Before You Begin 24
Handling the Printer 25
Select a Site for the Printer 26
Interface 27
Standard or 27
Optional on 27
Characteristics 27
I) may damage the 28
O) position 30
Power Cord Specifications 31
Types of Media 32
Ribbon Overview 34
Adhesive Test 35
Ribbon Scratch Test 35
Operations 37
Media Paths 38
Start a Roll of Media 39
Insert Media into the Printer 40
Fanfold Media 41
Load Media in Tear-Off Mode 42
4. Slide out the media guide 43
Close the printhead assembly 44
Load Media in Peel-Off Mode 45
Slide out the media guide 46
PAUSE to enable printing 49
Load Media in Cutter Mode 50
Load Ribbon 53
Remove Used Ribbon 57
Calibrate the Printer 58
Adjust the Reflective Sensor 59
Adjust Printhead Pressure 61
If the media... Then 62
Configuration 63
Setup Mode 64
If you wish to... Then 65
PASSWORD and the number 0000 66
Printing Configuration Labels 68
SETTINGS 69
NETWORK 70
Select a Display Language 71
DARKNESS 72
TEAR OFF 73
LABEL TOP 73
X FORMS ADJUST 73
LEFT POSITION 73
Y FORMS ADJUST 73
MEDIA TYPE 74
SENSOR SELECT 74
PRINT SPEED 75
PRINT WIDTH 75
KDU MODE 75
COMPAT. MODE 75
CONTROL CODES 76
RESOLUTION 76
Password Level 3 Parameters 77
MODULE A 78
MODULE B 78
PARALLEL COMM 78
PRINT PAGE 78
PRINT FORMAT 78
DATA BITS 79
STATUS RESPONSE 79
HOST HANDSHAKE 80
CONTROL CHAR 80
COMMAND CHAR 80
DELIM. CHAR 81
REPRINT MODE 81
CHANGE RTC DATE 81
Control Panel Parameters 82
ZPL OVERRIDE 83
SENSOR PROFILE 84
Parameter Explanation 85
To modify this parameter: 86
Routine Maintenance 87
Replacing Printer Components 88
Lubrication 88
Clean the Exterior 89
Cleaning Procedures 90
Clean the Peel Assembly 94
Close the media door 96
Clean the Cutter Module 97
Troubleshooting Checklists 100
RIBBON OUT 101
O) the printer 102
I) the printer 102
HEAD COLD 103
HEAD TOO HOT 103
DEFRAGMENTING 104
ERROR CONDITION 104
CUTTER JAM 104
HEAD ELE. BAD 104
Memory Errors 105
Print Quality Problems 106
Troubleshooting 107
Note • A vertical drift of 108
Calibration Problems 109
Communications Problems 110
YES, the printer 111
O) and then on (I) 112
O) and then 112
Printer Diagnostics 114
CANCEL Self Test 115
PAUSE Self Test 116
FEED Self Test 117
Print Quality Description 118
FEED and PAUSE Self Test 120
Sensor Profile 122
Specifications 125
General Specifications 126
Agency Approvals 127
Printing Specifications 128
Media Specifications 129
Ribbon Specifications 130
ZPL II Commands 131
Define Password 132
End User License 133
Agreement 133
End User License Agreement 134
Glossary 139
Cutter Jam message, 104 144
HEAD COLD message 145
HEAD ELEMENT BAD message, 102 145
HEAD TOO HOT message, 103 145
RIBBON IN message, 102 146
THERMISTOR FAULT message 147

Commentaires sur ces manuels

Pas de commentaire

Zebra Stripe Guide de l'utilisateur Page 51

Commentaires sur ces manuels

Produits connexes et manuels pour Imprimantes d'étiquettes Zebra Stripe