Zebra XiII-Series Manuel d'utilisateur télécharger pdf (Page 68)

Adjustments

Toggle Positioning

Both toggles should be positioned so that they provide even pressure on the

media. The toggles are positioned by sliding them to the desired location.

On media too narrow to accommodate both toggles, position one toggle

over the center of the media and decrease the pressure on the unused toggle.

NOTE: Make sure that the toggle pressure is even across the width of the

media, otherwise the media and/or ribbon may drift.

56 Zebra XiII-Series User’s Guide

ADJUSTING

NUTS

LABEL

AVAILABLE

SENSORS

Figure 14. Toggle Adjustment

H:...Xi2UsersGuideR2.vp

Fri Aug 07 10:36:19 1998

Color profile: Disabled

Composite Default screen

1 2 ... 63 64 65 66 67 68 69 70 71 72 73 ... 117 118

Zebra XiII-Series 1
Fri Aug 07 08:59:37 1998 2
Warranty Information 3
Contents 5
Operation 21 6
Fri Aug 07 10:33:15 1998 7
Options 71 8
Specifications 77 8
Appendix 87 9
Glossary 99 9
Index 103 9
H:...Xi2UsersGuideR2.vp 10
Fri Aug 07 10:33:16 1998 10
Color profile: Disabled 10
Composite Default screen 10
List of Figures 11
List of Tables 12
Getting Started 13
System Requirements 14
Media and Ribbon Requirements 15
Unpacking 15
Fri Aug 07 10:34:39 1998 16
Site Requirements 17
Communications 18
Loading Media 18
Non-Continuous Media 19
Continuous Media 19
Black-Mark Media 19
Tear-Off Mode Media Loading 20
REWINDPEEL-OFF 21
TEAR-OFF 21
CUTTER REWIND 21
BOTTOM SUPPLY REAR SUPPLY 22
Continuous Media Loading 23
Cutter Mode Media Loading 23
Rewind Mode Media Loading 23
Fri Aug 07 10:34:43 1998 24
Peel-Off Mode Media Loading 26
Transmissive Media Sensor 27
Position Adjustment 27
MEDIA SENSOR 28
ADJUSTMENT 28
Lower Media Sensor Adjustment 29
STRIP OF MEDIA 30
6-12 INCHES LONG 30
Fri Aug 07 10:34:46 1998 31
Ribbon Removal 32
Operation 33
Peel-Off Mode 34
Rewind Mode 34
Cutter Mode 34
Operator Controls 35
Front Panel Display 36
Front Panel Keys 37
Front Panel Lights 38
Printer Status Sensors 39
Initial Printer Power-Up 40
Configuration and Calibration 41
Fri Aug 07 10:35:48 1998 42
Leaving the Program Mode 43
Fri Aug 07 10:35:49 1998 45
Fri Aug 07 10:35:50 1998 50
Fri Aug 07 10:35:51 1998 54
Fri Aug 07 10:35:52 1998 57
Sample ZPL II Label Formats 58
Fri Aug 07 10:35:53 1998 62
Routine Care and Adjustment 63
Cleaning the Exterior 64
Cleaning the Interior 64
Cleaning the Sensors 65
Lubrication 66
Fuse Replacement 66
Fri Aug 07 10:36:17 1998 67
ADJUSTING 68
AVAILABLE 68
Printhead Pressure Adjustment 69
Fri Aug 07 10:36:20 1998 70
Fri Aug 07 10:36:37 1998 71
Fri Aug 07 10:36:38 1998 72
Printer Diagnostics 77
Cancel Key Self Test 78
Pause Key Self Test 79
Feed Key Self Test 80
Fri Aug 07 10:36:39 1998 81
Fri Aug 07 10:36:40 1998 82
Rewind Option 83
Memory SIMMs 84
On-Line Verifier 84
Applicator Interface 85
Media Supply Spindle 85
Optional Media Supply Fins 85
PCMCIA Type I Memory Cards 86
KMT Printhead 86
Communication Interfaces 86
RS-485 Interface 87
Fri Aug 07 10:36:58 1998 88
Specifications 89
Bar Codes 90
General Specifications 91
Printing Specifications 92
Ribbon Specification 92
Media Specifications 93
Fri Aug 07 10:37:27 1998 94
Standard 95
Optional Printer Fonts 97
@ABCDEFG 98
Appendix 99
Fri Aug 07 10:37:51 1998 100
RS-232 Interconnections 101
Fri Aug 07 10:37:52 1998 102
Rear Panel DB-25S 103
RS-422/RS-485 Connector 103
Parallel Data Port 104
Cabling Requirements 105
ASCII Code Chart 106
Fri Aug 07 10:37:54 1998 107
Too Dark 108
Slightly Dark 108
Slightly Light 108
Too Light 108
“In-Spec” 108
Figure 29. Bar Code Examples 109
Fri Aug 07 10:37:57 1998 110
Glossary 111
Fri Aug 07 10:38:13 1998 112
Fri Aug 07 10:38:14 1998 113
Fri Aug 07 10:38:32 1998 115

Commentaires sur ces manuels

Pas de commentaire

Zebra XiII-Series Manuel d'utilisateur Page 68

Commentaires sur ces manuels

Produits connexes et manuels pour Imprimantes d'étiquettes Zebra XiII-Series