Zebra TTPM2 Spécifications Page 56
- Page / 140
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Programming
Software Command Syntax
56
P1002902-002 TTP 2000 Technical Manual 09/14/2009
Cut And Present Commands
The paper is cut and ejected through the presenter module. The <RS> command automatically
gives the eject length of 50 mm in addition to the amount specified by parameter n47.
If the printout length is less than the minimum page length (75 mm or the value specified by
n37 and n38, whichever is greater), paper is fed until the minimum printout length is reached
before execution of any cut command.
<ESC><RS> causes the paper to be cut but performs no eject operation.
Eject can be effected with the <ESC><FF>
<n> command (see Eject (Run Presenter)
on page 57).
To avoid thin strips of paper in the printer, multiple cut commands without paper feed in-
between will not be performed. If the printout length is less than the minimum page length
(75 mm or the value specified by n37 and n38, whichever is greater), paper is fed until the
minimum printout length is reached before execution of any cut command.
Also, refer to the note in <RS> concerning the cut position with regard to the print line.
Text to be printed<CR><LF>
<ESC><RS>
<ESC><FF><30>
will print “Text to be printed” and cut and then eject 30 mm.
Important • The printer does not receive data while cut and present commands are executed.
RS
Cut and Eject
1E Hex
30 Decimal
Note • The cut position is 9 mm after the print line. This makes the last 72 dot lines of the
previous page end up on the beginning of the next page. To have the printer position the cut
after these dot lines, set parameter n49 = 1 (Advance before cut to automatic distance
calculation). The auto advance function also adds an additional 16 dot lines (2 mm) of feed
due to the width of the cutter blade.
If you prefer to set n49 to 0 (off), you can use a paper advance command to perform the same
task:
<ESC>J<88><RS>
This will position the cut 16 dot lines (2 mm) after the end of the print data.
ESC RS
Cut Only, No Eject
1B 1E Hex
27 30 Decimal
Note • Use the Cut Only command if you want full control over the printer from your
system. When using <ESC><RS>, you must add commands to feed to the correct cut
position (if n49 is not set to 1) and commands to eject the paper so that the customer can
retrieve the printout.
- Zebra® TTP 2000 1
- Technical Manual 1
- Contents 3
- Introduction 7
- Contacts 8
- TTP 2010 TTP 2020 TTP 2030 10
- Looping Presenter 11
- Controls 12
- Power Indicator 13
- Status Indicator 13
- Product Presentation 14
- Installation 15
- Installing a Paper Guide 16
- Installation Considerations 17
- Quick-Fit Hubs 18
- Using a Zebra Roll Holder 19
- Design Your Own Mounting 20
- Ambient Light 21
- Paper low 22
- Connecting the TTP 2030 24
- Connector 25
- Making a Self-Test Printout 26
- Self-test 27
- TTP 2030 Kiosk Printer 28
- Logotype No. 0 28
- Operation 29
- Installing a Paper Roll 30
- Thermal side (top) 31
- Cut off at 31
- 2. Lift the print head 32
- Programming 33
- Figure 24 • Printout Styles 34
- Description of command 35
- Mnemonic 35
- Hex representation of command 35
- Command Hex Decimal Function 37
- 1B 23 Hex 39
- 27 35 Decimal 39
- 1B 5A Hex 39
- 27 90 Decimal 39
- 1B 6F n1 hex 40
- 27 111 n1 decimal 40
- 1B 4E n1 hex 40
- 27 78 n1 decimal 40
- 1B 21 n1 hex 41
- 27 33 n1 decimal 41
- 1B 42 n1 Hex 41
- 27 66 n1 decimal 41
- Software Command Syntax 42
- 1B 77 n1 hex 43
- 27 119 n1 decimal 43
- 1B 74 n1...n5 data hex 43
- 27 116 n1...n5 data decimal 43
- <LF><RS> 46
- 1B 42 53 n1...n11 hex 47
- 27 66 83 n1...n11 decimal 47
- 1B 42 43 n1 hex 49
- 27 66 67 n1 decimal 49
- 1B 7C n1 nx Hex 49
- 027 124 n1 nx Decimal 49
- 1B 62 n1...n5 Data hex 51
- 27 98 n1...n5 Data decimal 51
- 1B 73 n1 Data Hex 51
- 27 115 n1 Data Decimal 51
- SW99006B 52
- 1B 4C n1 Hex 53
- 27 76 n1 Decimal 53
- 1B 67 n1...n5 hex 53
- 27 103 n1...n5 decimal 53
- Print Commands 54
- 1B 6A n1 hex 55
- 27 106 n1 decimal 55
- 1B 51 n1 hex 55
- 1B 81 n1 Decimal 55
- <ESC><RS> 56
- 05 Hex 58
- 5 Decimal 58
- 1B 66 n1 Hex 58
- 27 102 n1 decimal 58
- System Related Commands 59
- 1B 26 50 n1...n2 hex 61
- 27 38 80 n1...n2 decimal 61
- 1B 00 Hex 61
- 27 0 Decimal 61
- 1B 05 01 Hex 62
- 27 5 1 decimal 62
- 1B 05 02 hex 63
- 27 5 2 decimal 63
- 1B 05 04 hex 64
- 27 5 4 decimal 64
- 1B 05 05 hex 65
- 27 5 5 decimal 65
- 1B 05 06 hex 66
- 27 5 6 decimal 66
- 1B 05 0C hex 68
- 27 5 12 decimal 68
- 1B 05 63 hex 68
- 27 5 99 decimal 68
- 1B 05 45 hex 69
- 27 5 69 decimal 69
- 1B 05 50 n1 Hex 69
- 27 5 80 n1 Decimal 69
- 1B 06 n1 hex 70
- 27 6 n1 decimal 70
- Font Loading 71
- File Format 72
- Character Bitmap Data 73
- Logotypes 74
- Printing 75
- 5. Print the printout 76
- Status Reporting 77
- Default Parameter Settings 79
- Burn Time 80
- TTP model 81
- Page 2010 2020 2030 81
- Serial Interface Set-Up 82
- Flow-Control 83
- 1Default 84
- Print Setup 85
- 2 , 88 Default 90
- 2 , 48 Min 90
- 255 , 255 Max 90
- Fixed Document Mode 91
- Cut Position Calibration 93
- Wall Compensation (mm) 93
- Printable Area 100
- Black-mark on 101
- Black-mark and 101
- Page setup 102
- If your Firmware is 103
- Parameters Used 104
- If the paper… Then it is… 105
- Auto Cut-Offset 106
- Manual Cut-Offset 107
- FF (Form Feed) 107
- Interface 109
- Serial, TTP 2010 110
- Parallel, TTP 2020 111
- USB, TTP 2030 112
- Maintenance 113
- Fault Finding 114
- 2. Open the print head 115
- Firmware 116
- Specifications 119
- Auto Selected Print Widths 120
- Interfaces 120
- Direct Print Mode 121
- Miscellaneous 121
- Basic Character Set 122
- NA/LA/AP EMEA 123
- Accessories 124
- Dimensions 125
- Universal Roll Holder 126
- Media Roll 129
- Centering Guides 129
- Wall Mount Roll Holder 131
- 中国 RoHS 材料声明 133
- (China RoHS Material 133
- Declaration) 133
Produits connexes et manuels pour Imprimer et scanner Zebra TTPM2
(86 pages)
Imprimer et scanner Zebra CPCL Spécifications
(497 pages)
(497 pages)
Vitek VT-1609 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Entsafter Vitek VT-1609.
Wir stellen 1 PDF-Handbücher Vitek VT-1609 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Commentaires sur ces manuels