Zebra S400 Guide de l'utilisateur Page 135
- Page / 146
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
- ZM400/ZM600 1
- User Guide 1
- Declaration of Conformity 3
- Compliance Information 4
- Contents 5
- Who Should Use This Document 10
- Contacts 11
- Document Conventions 12
- FEED button 13
- CANCEL button 13
- About This Document 14
- Introduction 15
- External View 16
- Printer Media Compartment 17
- Control Panel 18
- Control Panel Buttons 19
- Control Panel Lights 20
- Printer Language Modes 21
- Printer Setup 23
- Before You Begin 24
- Handling the Printer 25
- Select a Site for the Printer 26
- Interface 27
- Standard or 27
- Optional on 27
- Characteristics 27
- I) may damage the 28
- O) position 31
- Power Cord Specifications 32
- Types of Media 33
- Ribbon Overview 35
- Ribbon Scratch Test 36
- Operations 37
- Media Paths 39
- Media Path 40
- Load Media 41
- Rear Feed 42
- Bottom Feed 42
- Roll Media (Continued) 43
- Fanfold Media (Continued) 43
- PAUSE to enable printing 44
- Close the printhead assembly 54
- Load Ribbon 55
- Ribbon Coated Outside 57
- (black ribbon spindle) 57
- Ribbon Coated Inside 57
- (gray ribbon spindle) 57
- Remove Used Ribbon 59
- Calibrate the Printer 60
- Adjust Printhead Pressure 61
- Inside Dial Outside Dial 62
- Configuration 63
- Setup Mode 64
- Exit Setup Mode 65
- Default Password Value 66
- Print a Configuration Label 67
- LIST NETWORK 68
- Control Panel Parameters 69
- Standard Printer Parameters 70
- To change the value shown: 71
- Parameter 71
- ZM400 ZM600 74
- Action/Explanation 75
- WARNING REPLACE 77
- To format a memory card: 80
- To initialize Flash memory: 81
- To print a sensor profile: 81
- LOAD BACKING prompt displays 82
- RELOAD ALL displays 82
- To skip these parameters: 90
- IDLE DISPLAY 92
- Replacing Printer Components 96
- Lubrication 96
- Clean the Exterior 97
- Routine Maintenance 100
- Cleaning Procedures 100
- Clean the Cutter Module 102
- I) the printer 103
- Troubleshooting 107
- Troubleshooting Checklists 108
- LCD Error Messages 109
- O) the printer 110
- HEAD COLD 111
- HEAD TOO HOT 111
- DEFRAGMENTING 112
- ERROR CONDITION 112
- CUTTER JAM 112
- OUT OF MEMORY 112
- (function) 112
- Print Quality Problems 113
- Note • A vertical drift of 115
- Calibration Problems 116
- Communications Problems 117
- Ribbon Problems 118
- LANGUAGE 119
- SAVE CHANGES in the 119
- Printer Diagnostics 121
- CANCEL Self Test 122
- PAUSE Self Test 123
- FEED Self Test 124
- Print Quality Description 126
- FEED and PAUSE Self Test 127
- Sensor Profile 129
- Specifications 131
- General Specifications 132
- Agency Approvals 133
- Printing Specifications 134
- Media Specifications 136
- Ribbon Specifications 137
- Printer Options 138
- Cutter Jam message, 104 140
- HEAD COLD message 140
- HEAD ELEMENT BAD message, 102 140
- HEAD TOO HOT message, 103 140
- INVALID HEAD message, 101 141
- OUT OF MEMORY message, 104 141
- PAPER OUT message, 102 142
- RIBBON IN message, 102 143
- RIBBON OUT message, 101 143
- THERMISTOR FAULT message 144
- © 2007 ZIH Corp 146
Produits connexes et manuels pour Imprimantes d'étiquettes Zebra S400
(102 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.101 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels