Zebra 105SL Plus Guide de l'utilisateur Page 34
- Page / 180
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Introduction
Control Panel Display
34
P1056468-002 7/3/13
Set the Subnet Mask*
View and, if necessary, change the subnet mask.
Changes are saved only if IP PROTOCOL is set to
PERMANENT.
To allow any saved changes to take effect, use RESET NETWORK
on page 35 to reset the print server.
See Subnet Mask on page 98 for more information.
* This menu item appears only if a wired or wireless print server
is installed in your printer.
Set the Default Gateway*
View and, if necessary, change the default gateway.
Changes are saved only if IP PROTOCOL is set to
PERMANENT.
To allow any saved changes to take effect, use RESET NETWORK
on page 35 to reset the print server.
See Default Gateway on page 98 for more information.
* This menu item appears only if a wired or wireless print server
is installed in your printer.
View the MAC Address*
View the Media Access Control (MAC) address of the print server
that is installed in the printer (wired or wireless).
See MAC Address on page 98 for more information.
* This menu item, which cannot be modified from the control
panel, appears only if a wired or wireless print server is
installed in your printer.
View the ESSID Value*
The Extended Service Set Identification (ESSID) is an identifier
for your wireless network. This setting, which cannot be modified
from the control panel, gives the ESSID for the current wireless
configuration.
See ESSID on page 99 for more information.
* This menu item, which cannot be modified from the control
panel, appears only if a wireless print server is installed in your
printer.
- 105SLPlus™ 1
- User Guide 1
- Part Number: P1056468-002 2
- Declaration of Conformity 3
- Compliance Information 4
- Contents 5
- Who Should Use This Document 10
- Document Conventions 11
- About This Document 12
- Introduction 13
- Printer Components 14
- Control Panel 15
- Control Panel Display 17
- Perform an action 18
- Change Parameter Values 18
- Default Password Value 20
- WARNING CLEAN PRINTHEAD 23
- YES to reset 23
- WARNING REPLACE HEAD 24
- 3. Do you want to continue? 26
- PERMANENT 33
- Printer Setup and 37
- Operation 37
- Handling the Printer 38
- Printer Setup and Operation 39
- I) may damage the 40
- Data Cables 42
- 115 V AC 43
- 230 V AC 43
- Power Cord Specifications 44
- Printer Setup 46
- Types of Media 47
- Ribbon Overview 49
- Adhesive Test 50
- Ribbon Scratch Test 50
- Select a Print Mode 51
- Load the Ribbon 54
- If… Then… 55
- 2) until it locks into place 58
- Load the Media 59
- 1) all the way out 60
- Bottom Feed 61
- Rear Feed 61
- RIBBON OUT error 62
- 1), under the 63
- Rewind Mode on page 72 64
- Mode on page 77 64
- 11. Close the media door 66
- Printer Configuration 81
- Print Settings 83
- ~JS when received 87
- • the non-resettable counter 90
- Important • 94
- Directory Listing 95
- Network Settings 96
- Print Server Settings > 99
- Factory Print Server Settings 99
- Language Settings 100
- • ZPL II 101
- Sensor Settings 102
- Port Settings 103
- Changing Printer Settings 104
- DSR/DTR for host handshake 105
- ZEBRA response messages are 105
- LOAD BACKING 106
- Raise the media door 107
- If you are using… Then… 108
- REMOVE RIBBON 109
- CALIBRATING 110
- PLEASE WAIT 110
- RELOAD ALL 110
- Close the media door 111
- Remove Used Ribbon 112
- If... Then 113
- Pull out the spindle hook 114
- Upper Media Sensor 115
- Routine Maintenance 116
- Lower Media Sensor 118
- Toggle Position Adjustment 119
- I) the printer.) 120
- Printhead Pressure Adjustment 121
- Replacing Printer Components 124
- Lubrication 124
- CLEAN HEAD NOW appears 125
- Clean the Sensors 128
- Transmissive Media Sensor 129
- Clean the Snap Plate 130
- Clean the Cutter 134
- Troubleshooting 135
- Printing Issues 136
- Error Messages 139
- 1) is likely 140
- O) the printer 141
- I) the printer 141
- Display/ 143
- Printer Condition 143
- Calibration Problems 144
- Communications Problems 145
- Ribbon Problems 146
- Miscellaneous Issues 147
- Printer Diagnostics 148
- CANCEL Self Test 149
- PAUSE Self Test 150
- FEED Self Test 151
- Print Quality Description 152
- FEED + PAUSE Self Test 154
- CANCEL + PAUSE Self Test 154
- FE indicates a framing error 155
- PE indicates a parity error 155
- NE indicates noise 155
- Sensor Profile 156
- MEDIA (3) for the media 157
- Specifications 159
- Features 160
- Bar Codes 161
- General Specifications 162
- Print Specifications 163
- Media Specifications 164
- Ribbon Specifications 165
- Glossary 167
- 7/3/13 P1056468-002 171
- P1056468-002 7/3/13 172
- 7/3/13 P1056468-002 173
Produits connexes et manuels pour Imprimer et scanner Zebra 105SL Plus
Imprimer et scanner Zebra 105Se Spécifications
(110 pages)
(110 pages)
Imprimer et scanner Zebra TTPM2 Spécifications
(140 pages)
(140 pages)
(86 pages)
Imprimer et scanner Zebra CPCL Spécifications
(497 pages)
(497 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.062 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels