Zebra 110PAX4 Guide de l'utilisateur Page 45
- Page / 164
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
45
Operations
Load Media
6/29/11 110PAX4/R110PAX4 User Guide 57512L-004 Rev. A
13. Thread the media liner around the peel bar (1), under the media liner roller (2), and
through the peel roller assembly (
3).
14. Rotate the peel roller assembly (1) up until it locks into the closed position.
15. Thread the media liner around the take-up spindle of the applicator (refer to the
applicator’s user guide).
16. Close the media door.
Note • If the applicator has an air tube, route the media liner between the air tube and the
peel bar. Do not thread the media liner over the air tube.
3 2
1
1
- 110PAX4™/R110PAX4™ 1
- User Guide 1
- Part Number: 57512L-004 2
- DECLARATION OF INCORPORATION 3
- Compliance Information 4
- Contents 5
- Who Should Use This Document 10
- T: Telephone 11
- F: Facsimile 11
- E: E-mail 11
- Bubbledot ICG font 12
- Liquid Crystal Display (LCD) 13
- Lights/LEDs 13
- About This Document 14
- Document Conventions 14
- Introduction 15
- Print Engine Exterior View 16
- Control Panel 17
- CANCEL is ignored 18
- CANCEL until 18
- Power On/Off Switch 20
- Print Engine Setup 21
- Before You Begin 22
- Handling the Print Engine 23
- Recycle the Print Engine 24
- Print Engine Installation 25
- 5 mounting screws 26
- - 0.218 in. (5.5 mm) through 26
- Power Cord Specifications 34
- Types of Media 35
- Ribbon Overview 37
- Adhesive Test 38
- Ribbon Scratch Test 38
- Operations 39
- Load Media 40
- Left-Hand Right-Hand 41
- 16. Close the media door 45
- Load Ribbon 46
- Figure 16 • Loaded Ribbon 47
- 1) until it latches onto the 51
- Remove Used Ribbon 52
- Calibrate the Print Engine 53
- Transmissive Media Sensor 55
- Ribbon Sensor 55
- Reflective Media Sensor 55
- If the media... Then 56
- Configuration 57
- Setup Mode 58
- Exit Setup Mode 59
- Default Password Value 60
- LIST SETUP 61
- LIST NETWORK 62
- Control Panel Parameters 63
- Parameter Action/Explanation 64
- To change the value shown: 64
- BACKFEED SPEED 65
- 2 IPS + 65
- TEAR OFF +000 65
- - + 65
- Parameter 66
- PRINT WIDTH 67
- - 168 0/8 MM + 67
- MAXIMUM LENGTH 68
- 39.0IN 988MM 68
- To reset the media counter: 70
- To reset the ribbon counter: 70
- Action/Explanation 73
- To format a memory card: 74
- To initialize Flash memory: 75
- SENSOR PROFILE 76
- PRINT 76
- LEFT POSITION 83
- - ±0000 + 83
- HEAD RESISTOR 83
- - 0500 OHMS + 83
- APPLICATOR PORT 84
- - OFF + 84
- ERROR ON PAUSE 84
- - ENABLED + 84
- ^SP command 86
- To skip these parameters: 87
- CLEAN HEAD NOW appears 90
- Clean the Media Compartment 91
- Clean the Sensors 91
- Door-open sensor 92
- Ribbon sensor reflector 92
- Ribbon sensor 92
- Toggle Positioning 95
- I) the printer.) 96
- 7/16 inch 97
- Printhead Pressure Adjustment 98
- Routine Maintenance 100
- Power Fuse Replacement 100
- Troubleshooting 101
- Troubleshooting Checklists 102
- ERROR CONDITION 103
- RIBBON OUT 103
- O) the print engine 104
- I) the print engine 104
- HEAD COLD 105
- HEAD TOO HOT 105
- DEFRAGMENTING 106
- OUT OF MEMORY 106
- (function) 106
- Memory Errors 107
- Print Quality Problems 108
- Note • A vertical drift of 110
- NONE. See 112
- Ribbon Problems 113
- RFID Problems 114
- LANGUAGE 117
- SAVE CHANGES in the 117
- Print Engine Diagnostics 119
- CANCEL Self Test 120
- PAUSE Self Test 121
- FEED Self Test 122
- Print Quality Description 124
- FEED and PAUSE Self Test 126
- Parameter Controlled By 127
- J8 Interface Fixed 128
- J7 Interface Fixed 128
- Twinax/Coax ID ZPL 128
- Sensor Profile 130
- Data Ports 131
- Parallel Data Port 132
- 36-Pin Connectors 133
- Serial Data Port 134
- Pin Configuration 135
- RS-232 Interface Connections 136
- Modem Connection 137
- Applicator Signals 138
- Caution • Replace 140
- Isolated (External Power) 144
- Non-Isolated (Internal Print 144
- Engine Power) 144
- Fuse and Jumper Locations 145
- Specifications 147
- General Specifications 148
- Communications Specifications 149
- Other Standard Features 150
- Additional Options 150
- Agency Approvals 151
- Media Specifications 153
- Ribbon Specifications 154
- Printing Specifications 155
- Bar Codes 156
Produits connexes et manuels pour Imprimer et scanner Zebra 110PAX4
Imprimer et scanner Zebra TTPM3 Spécifications
(112 pages)
(112 pages)
Imprimer et scanner Zebra 105Se Spécifications
(110 pages)
(110 pages)
Imprimer et scanner Zebra TTPM2 Spécifications
(140 pages)
(140 pages)
(86 pages)
Imprimer et scanner Zebra CPCL Spécifications
(497 pages)
(497 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.733 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels