Zebra 170PAX4 Guide de l'utilisateur télécharger pdf (Page 42)

Operations

Load Media

57516L-002 Rev. A 170PAX4 User Guide 1/10/06

To load media, complete these steps:

1. Load media on the media supply reel of the applicator (refer to the applicator’s user

guide).

2. Open the media door.

3. Press down on the pinch roller release latch.

The pinch roller assembly springs up.

4. Under the print engine, grasp the brass thumb nut (1) of the outer media guide (2), and

slide the outer media guide all the way out.

1 2 ... 37 38 39 40 41 42 43 44 45 46 47 ... 163 164

User Guide 1
DECLARATION OF INCORPORATION 3
Compliance Information 4
Contents 5
Who Should Use This Document 10
Contacts 11
Document Conventions 12
About This Document 13
Introduction 15
Print Engine Exterior View 16
Control Panel 17
Description/Function 18
Power On/Off Switch 20
Print Engine Setup 21
Before You Begin 22
Handling the Print Engine 23
Print Engine Installation 24
Mounting screws (four total) 28
Applicator 28
Power Cord Specifications 30
Connector Locations 31
Types of Connections 32
Data Cable Requirements 34
Types of Media 35
Ribbon Overview 37
Adhesive Test 38
Ribbon Scratch Test 38
Operations 39
Load Media 40
Figure 21 • Loaded Media 41
2. Open the media door 42
16. Close the media door 46
Load Ribbon 47
Figure 24 • Loaded Ribbon 48
9. Close the media door 51
Remove Used Ribbon 52
Calibrate the Print Engine 53
Ribbon Sensor 55
Reflective Media Sensor 55
Transmissive Media Sensor 55
If the media... Then 56
Configuration 57
Setup Mode 58
Exit Setup Mode 59
Default Password Value 60
Print a Configuration Label 61
LIST NETWORK 62
Control Panel LCD Displays 63
6 IPS + 64
BACKFEED SPEED 64
2 IPS + 64
SLEW SPEED 64
TEAR OFF +000 65
- + 65
PRINT MODE 65
-APPLICATOR + 65
Action/Explanation 66
MAXIMUM LENGTH 67
-39.0 IN 988 MM 67
To change the value shown: 68
Parameter 68
To reset the media counter: 69
To reset the ribbon counter: 69
To format a memory card: 73
To initialize Flash memory: 74
SENSOR PROFILE 75
PRINT 75
COMMUNICATIONS 79
- NORMAL MODE + 79
CONTROL PREFIX 79
- < >7EH + 79
PERMANENT save option 81
RIBBON TENSION 81
- HIGH + 81
MEDIA POWER UP 81
- CALIBRATION + 81
LEFT POSITION 83
- ±0000 + 83
HEAD RESISTOR 83
- 0500 OHMS + 83
APPLICATOR PORT 84
- OFF + 84
ERROR ON PAUSE 84
- ENABLED + 84
^SP command 86
To skip these parameters: 87
Print Server LCD Displays 89
^WE ZPL command to set 91
Parameter Action/Explanation 92
Lubrication 94
Cleaning Schedule 94
Clean the Exterior 94
Clean the Media Compartment 95
Clean the Sensors 95
Door-open sensor 96
Toggle Positioning 99
Printhead Pressure Adjustment 100
Power Fuse Replacement 101
Routine Maintenance 102
Troubleshooting 103
Troubleshooting Checklists 104
LCD Error Messages 105
OUT OF MEMORY 107
(function) 107
HEAD COLD 107
Memory Errors 108
Print Quality Problems 109
Note • A vertical drift of 111
Communications Problems 113
LANGUAGE 114
SAVE CHANGES in the 114
Calibrate 115
Print Engine Diagnostics 116
CANCEL Self Test 117
PAUSE Self Test 118
FEED Self Test 119
Print Quality Description 121
FEED and PAUSE Self Test 123
Parameter Controlled By 124
Data Ports 127
Parallel Data Port 128
36-Pin Connectors 129
Serial Data Port 130
Pin Configuration 131
RS-232 Interface Connections 132
Modem Connection 133
Applicator Signals 134
Isolated (External Power) 140
Non-Isolated (Internal Print 140
Engine Power) 140
Fuse and Jumper Locations 141
Specifications 143
General Specifications 144
Other Standard Features 145
Additional Options 145
Agency Approvals 146
Media Specifications 147
Ribbon Specifications 148
Printing Specifications 149
Bar Codes 150
Glossary 151
HEAD TOO HOT 156
PAPER OUT 158
RIBBON IN 159
RIBBON OUT 159

Commentaires sur ces manuels

Pas de commentaire

Zebra 170PAX4 Guide de l'utilisateur Page 42

Commentaires sur ces manuels

Produits connexes et manuels pour Imprimer et scanner Zebra 170PAX4