Zebra lLink APL-I Manuel d'utilisateur Page 99
- Page / 118
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
99
Control Panel Options
Control Panel Options
11/24/09 APL-I Reference Guide 14177L-003
333
3
RESET CNTR1
This allows you to reset the advanced counter
used by the printer to monitor the label
generation in inches, centimeters, and number of
labels.
333
3
RESET CNTR2
This allows you to reset the advanced counter
used by the printer to monitor the label
generation in inches, centimeters, and number of
labels.
333
3
PRINT METERS
This allows you to view the current date and
change the date.
Password Protected.
333
3
LIST ZPL SETUP
This prints a configuration label.
33333
3
APL-I SW SETUP
This allows you to print out the software
configuration label.
33333
3
APL-I HW SETUP
This allows you to print out the hardware
configuration label.
33333
3
APL-I PRNT QUAL.
This allows you to print out the print quality
test label.
33333
3
APL-I PITCH PRINT
This allows you to print the pitch test label.
33333
3
LIST NETWORK
This allows you to print a network
configuration label, which lists the settings for
the various Zebra print servers.
33333
3
PRINT PAGE
This allows you to print out a page format that
was previously sent to the printer by pushing a
single button. The number in the lower hand
corner of the control panel corresponds to the
page number that is printed.
33333
3
PRINT FORMAT
This allows you to print out a single format that
was previously sent to the printer by pushing a
single button. The number in the lower left
hand corner of the control panel corresponds to
the format number that is printed.
333 3
FORMAT CARD
This allows you to erase all information from
the memory card.
Password protected.
Table 3 • Control Panel Differences on Supported Printers (Continued)
XiIIIPlus
Z4Mplus/Z6Mplus
105SL
ZM400/ZM600
PAX4
Xi4
Control Panel Option Details and Menu Choices
- ZebraLink™ 1
- Part Number: 14177L-003 2
- Contents 3
- Who Should Use This Document 10
- Contacts 11
- Icons Used 12
- Related Documents 13
- About This Document 14
- Introduction 15
- Firmware 16
- Control Panel 16
- Troubleshooting 17
- Overview 18
- Commands 19
- Abort Print Job 20
- Error Code, Request 20
- Status Dump 21
- Status Enquiry 21
- Advanced Mode, Select 22
- Batch Count, Set 22
- Clear All Data 23
- Command Terminator 1 23
- Command Terminator 2 23
- Print Commands 24
- Emulation Mode, Enter 25
- Field, Select 26
- Field Decrement, Set 26
- Field Increment, Set 26
- Font, Transmit 27
- Form Feed 27
- Format, Select 28
- Format, Transmit 28
- Memory Usage, Transmit 29
- Numeric Field Separator 30
- Options Selected, Transmit 30
- Page, Select 31
- Page, Transmit 31
- Print 32
- Program Mode, Enter 32
- Program Number, Transmit 32
- Quantity Count, Set 33
- Warm Boot 34
- Amount of Storage, Define 35
- Auto-Transmit 1, Enable 35
- Auto-Transmit 2, Enable 35
- Auto-Transmit 3, Enable 36
- Cutter, Enable or Disable 36
- Dark Adjust, Set 37
- Intercharacter Delay, Set 38
- Label Rest Point, Adjust 39
- Label Retract Distance, Set 40
- Label Stock Type, Select 40
- Label Width, Set 40
- Maximum Label Length, Set 41
- Media Sensitivity, Select 41
- Message Delay, Set 41
- Number of Image Bands, Set 42
- Postamble, Set 42
- Preamble, Set 42
- Print Speed, Set 43
- Printer Language, Select 43
- Top of Form, Set 44
- Bar Code, Select Type 45
- Code 39 46
- Code 93 46
- Interleaved 2 of 5 47
- Code 2 of 5 47
- Codabar 48
- Code 11 48
- Code 128 49
- UPC/EAN 50
- HIBC Code 39 51
- Code 16K 52
- Code 49 52
- POSTNET 53
- Intermec 3400D Printer Label 54
- APL-I Printer Label 54
- Error Detection Characters 55
- Generated 55
- = disables truncating 56
- = enables truncating 56
- MaxiCode 57
- JIS-ITF 58
- HIBC Code 128 59
- Program Mode Commands 60
- QR Code 61
- MicroPDF417 62
- Note • Things to be aware of: 63
- Box Field, Create or Edit 66
- Command Tables, Load 68
- Current Edit Session, Save 68
- Field, Delete 69
- Field Data, Define Source 69
- Field Direction, Define 70
- Field Origin, Define 70
- Font Character Width, Define 70
- Font Type, Select 71
- Format, Create or Edit 71
- Format, Erase 72
- Graphic, Select 73
- Graphic or UDC, Define 73
- Interpretive Field, Edit 74
- Line Field, Create or Edit 75
- Outline Font, Download 76
- Page, Create or Edit 76
- Page, Delete 76
- Pitch Size, Set 77
- Point Size, Set 77
- Program Mode, Exit 77
- 1 – 9999 79
- Ambient Temperature, Transmit 80
- Command Terminator 80
- Dark Adjust 80
- Factory Defaults, Reset 80
- Formats, Print 81
- Pages, Print 82
- Pitch Label, Print 82
- Print Quality Label, Print 83
- Test and Service Commands 84
- Test and Service Mode, Exit 86
- User-Defined Fonts, Print 87
- Set-Get-Do (SGD) Commands 88
- Network Configuration 89
- Supported Print Servers 90
- Configuration 91
- Supported Protocols 91
- Defaulting the 10/100 PS 91
- Defaulting the Wireless PS 93
- Control Panel Options 95
- Protected Menus 96
- Password protected 100
- ZM400/ZM600 101
- XiIIIPlus 105
- Z4Mplus/Z6Mplus 105
- S4M LCD Options 106
- Supported Menu 107
- RESOLUTION 108
- PRINT WIDTH 108
- LCD Details 109
- Numerics 111
© 2020, manymanuals.fr. Tous droits réservés | 0.063 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels