Zebra Z4Mplus Manuel d'utilisateur Page 61
- Page / 178
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Communication
System Considerations
Z4Mplus and Z6Mplus User Guide 31
communication parameters. The values selected must be the same as those used by the
host equipment connected to the printer.
Parallel Port Communicating using the parallel port (see the parallel illustration
below), does not require special settings. The serial settings do not affect the parallel
port. Refer to Parallel Data Port on page 131 for further information.
Printer
Computer
Null modem adaptor
(if using a standard
modem cable)
Male
25
9
9
9
50 ft. (15 mm) maximum
- User Guide 1
- Your Feedback Is Important 3
- Feedback Form 4
- Proprietary Statement 5
- FCC Compliance Statement 6
- Liability Disclaimer 6
- Limitation of Liability 6
- Copyrights 7
- DECLARATION OF CONFORMITY 9
- Warranty Information 11
- Printer Products 12
- Printhead Warranty Period 12
- Supplies Products 13
- Agreement 14
- Table of Contents 21
- Contents 25
- Contacts 26
- About this Document 27
- Document Conventions 28
- Related Documents 30
- Introduction 31
- Inspect the printer 32
- Front Panel 33
- Printer Side View 35
- Printer Setup 37
- Before You Begin 38
- Types of Media 40
- Continuous Media 41
- Print Mode 42
- Load Media and Ribbon 43
- Load the Ribbon 44
- Printhead Pressure Adjustment 46
- Set Printhead Pressure 47
- Rewind Media Alignment 48
- Configuration Label 49
- Basic Configuration 52
- Basic Configuration Process 53
- Position the Label Sensor 56
- Transmissive Sensor 58
- Communication 59
- System Considerations 60
- Cable Requirements 62
- Printer Basics 63
- Printer Overview 64
- Front Panel Keys 66
- Front Panel Lights 67
- Load Roll Media 68
- Cutter Mode 70
- Peel-Off Mode 72
- Liner Take-Up Mode 74
- Liner Slide Tab 76
- Liner Slide 76
- Liner Removal 79
- Rewind Mode 79
- PAUSE to enable printing 80
- Load Fanfold Media 82
- Bottom Feed 83
- Rear Feed 83
- Remove the Ribbon 86
- Leave the Setup Mode 90
- Configuration 100
- Selecting ZPL Mode 106
- Label Positioning Parameters 108
- SAVE SETTINGS 114
- PRINTER READY 114
- Routine Care and Adjustments 115
- Cleaning Procedures 116
- Clean the Exterior 117
- Clean the Interior 117
- Clean the Sensors 119
- Clean the Rewind Option 120
- Clean the Peel-Off Assembly 122
- Clean the Cutter Module 123
- Lubrication 124
- Fuse Replacement 125
- Troubleshooting 127
- Error Conditions 128
- Load Roll Media 129
- page 15) 129
- (page 64) and select 130
- Warnings 131
- Warning — CUTTER JAM 132
- OUT OF MEMORY* 132
- page 87 133
- Wrinkled ribbon 134
- Calibration 135
- Communication Problems 136
- Print Quality Problems 137
- Printer Diagnostics 138
- Cancel Self Test 139
- Pause Self Test 140
- Feed Self Test 141
- Loading Factory Defaults 142
- Specifications 143
- General Specifications 144
- Printing Specifications 145
- Media Specifications 146
- Ribbon Specifications 148
- °, 90°, 180°, 270°) 150
- Bar codes 151
- AC Power Cord 152
- DB-9 Connectors 153
- Serial Data Communications 154
- Cable Specifications 154
- (Printer) 157
- (Modem, etc.) 157
- Connector 159
- Parallel Data Port 161
- Memory Cards 165
- Extend Printhead Life 169
- Challenge 170
- Preventive Maintenance 171
- Save-a-Printhead 172
Produits connexes et manuels pour Imprimantes d'étiquettes Zebra Z4Mplus
(86 pages)Vitek VT-1609 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Entsafter Vitek VT-1609.
Wir stellen 1 PDF-Handbücher Vitek VT-1609 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Commentaires sur ces manuels