Zebra TTP7030 Spécifications Page 109
- Page / 144
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
109
Maintenance
Printer Disassembly
02/11/2009 TTP 7020™/TTP 7030™ Technical Manual P1003636-001
Print Module
Removal
1. Remove the plastic cover by removing the two nuts holding it.
2. Disconnect the flat cable that interconnects the control board and the print module.
3. Flip the print module fully backward.
4. Unhook the two springs from the print module using a spring hook or a pair of pliers.
5. Return the print module to the normal operating position and lift it straight up.
Replacement
Install the print module in the reverse order.
Control Board
Removal
1. Loosen the four screws holding the control board module to the printer.
2. Remove the module and disconnect all cables from the control board.
3. Remove the four screws holding the board, and remove it.
Replacement
Install the control board in the reverse order.
Note • When the printer is assembled, load new firmware to the printer. See page .
- Zebra® TTP 7020™/TTP 7030™ 1
- Technical Manual 1
- Contents 3
- Identification Labels 8
- Introduction 10
- Contacts 10
- Product Presentation 11
- Indicators 13
- Feed-Forward (FF) Button 14
- Installation 15
- Installation Considerations 16
- Ambient Light 17
- Connecting To The Computer 18
- Connecting The Power 20
- Making A Test Printout 21
- Installing A Printer Driver 22
- Category Settings Notes 23
- • Roll paper 58 mm / 80 mm / 23
- • 1 to 9999 23
- • Enabled 23
- • Disabled 23
- Paper Level Sensors 26
- Operation 29
- Installing a Paper Roll 30
- Cut off at 31
- Clearing Paper Jams 32
- Programming 33
- Figure 17 • Ticket Styles 34
- Mnemonic 35
- Examples 35
- 1B 23 n1 Hex 38
- 27 35 n1 decimal 38
- 1B 5A Hex 38
- 27 90 Decimal 38
- 1B 6F n1 hex 39
- 27 111 n1 decimal 39
- 1B 4E n1 hex 39
- 27 78 n1 decimal 39
- Text Commands 40
- 1B 77 n1 hex 42
- 27 119 n1 decimal 42
- 1B 74 n1...n5 data hex 42
- 27 116 n1...n5 data decimal 42
- 2. Ignore LF 43
- Barcode Commands 45
- 1B 42 53 n1...n11 hex 47
- 27 66 83 n1...n11 decimal 47
- 027 066 087 n1 nx Decimal 48
- 1B 42 43 n1 hex 48
- 27 66 67 n1 decimal 48
- 1B 42 57 n1 nx Hex 48
- 1B 7C n1 nx Hex 49
- 027 124 n1 nx Decimal 49
- 1B 62 n1...n5 Data hex 50
- 27 98 n1...n5 Data decimal 50
- 1B 73 n1 Data Hex 50
- 27 115 n1 Data Decimal 50
- X start Y start 51
- X stop Y stop 51
- 3=checkered 51
- 1B 67 n1...n5 hex 52
- 27 103 n1...n5 decimal 52
- 1B 4C n1 Hex 52
- 27 76 n1 Decimal 52
- Print Commands 53
- 1B 6A n1 hex 54
- 27 106 n1 decimal 54
- 1E Hex 55
- 30 Decimal 55
- 1B 1E Hex 55
- 27 30 Decimal 55
- 1B 0C n1 hex 56
- 27 12 n1 decimal 56
- 19 n1 Hex 56
- 25 n1 Decimal 56
- 05 Hex 57
- 5 Decimal 57
- System Related Commands 58
- 1B 26 50 n1...n2 hex 60
- 27 38 80 n1...n2 decimal 60
- 1B 00 Hex 60
- 27 0 Decimal 60
- Error code Meaning 61
- 1B 05 02 hex 62
- 27 5 2 decimal 62
- 1B 05 04 hex 63
- 27 5 4 decimal 63
- 1B 05 06 hex 64
- 27 5 6 decimal 64
- Status Reporting Commands 65
- 1B 05 0B hex 66
- 27 5 11 decimal 66
- 1B 05 0C hex 66
- 27 5 12 decimal 66
- 1B 05 63 hex 67
- 27 5 99 decimal 67
- 1B 05 50 n1 Hex 67
- 27 5 80 n1 Decimal 67
- 1B 06 n1 hex 68
- 27 6 n1 decimal 68
- Font Loading 69
- Character bitmap data: 70
- Logotypes 71
- Printing 72
- 5. Print the printout 73
- Default Parameter Settings 74
- SW 02001 75
- Default Value 76
- Summary Of Parameter Settings 77
- Serial Interface Set-Up 78
- 2Default 79
- 0Default 80
- Print Setup 81
- Document mode 84
- 37 & 38 84
- Page length 84
- Fixed Document Mode 85
- Presenter mode 87
- Eject calibration constant 87
- Page Setup 89
- Printable Area 90
- SW95001B 91
- Parameters Used 93
- FF (Form Feed) 95
- 0 x 0.125 = 25mm 96
- Simple Calibration Process 97
- Parallel, TTP 7020 100
- • Head lifted 101
- • Cutter not home 101
- • Out of paper 101
- Setup Options 102
- Maintenance 103
- Fault Finding 104
- Sympton Suggest Actions 105
- Cleaning The Print Head 106
- Removing The Print Head 106
- Installing The Print Head 107
- Printer Disassembly 108
- Print Module 109
- Control Board 109
- Cutter Module 110
- Presenter Module 110
- Replacement Parts 111
- 1. Fit one hub screw 112
- If… Then… 113
- Bootware 114
- Firmware History 114
- FW Version Change 115
- Bug fixes 115
- New functions 115
- Small improvements 116
- Bar Code 117
- Black Mark 117
- Commands 118
- Firmware 118
- Interface 119
- Parallel 119
- Specifications 121
- Print Data 122
- Orientation 123
- Vertical (Landscape mode) 123
- Basic Character Set 124
- Paper Handling 126
- Printer Dimensions 127
- Environmental Conditions 127
- Miscellaneous 128
- Paper Specification 128
- Thermal coating 129
- Perforation 129
- Preprinting 129
- Black Mark Size and Position 130
- Print Width: 80 mm 112 mm 131
- IEC320/C14 132
- Ordering Numbers 133
- Print Width 80 mm 112 mm 134
- Numerics 139
- Part Number: P1003636-001 144
- © 2009 ZIH Corp 144
Produits connexes et manuels pour Imprimer et scanner Zebra TTP7030
Imprimer et scanner Zebra EPL2 Spécifications
(154 pages)
(154 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.099 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels