Zebra RZ Series Guide de l'utilisateur Page 85
- Page / 154
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
85
Configuration
Standard Control Panel Parameters
1/11/11 Z Series
®
/RZ™ Series User Guide 79695L-003
Calibrate Media and Ribbon Sensor Sensitivity
Use this procedure to adjust sensitivity of media and ribbon sensors.
Important • Follow this procedure exactly as presented. All of the
steps must be performed even if only one of the sensors requires
adjustment. You may press
MINUS (-) at any step in this procedure
to cancel the process.
To perform a media and ribbon sensor calibration:
1. Press SELECT to select the parameter.
2. Press PLUS (+) to start the calibration procedure.
The
LOAD BACKING prompt displays.
1. Open the printhead.
2. Remove approximately 8 in. (203 mm) of labels from the backing
(liner), and pull the media into the printer so that only the backing is
between the media sensors.
3. If your printer has the Peel-Off, Liner Take-Up, or Rewind option,
complete the following substeps:
a. Push down the peel-off mechanism release lever to open the peel
assembly.
b. Feed the liner over the tear-off/peel-off bar (1) and behind the peel
assembly (
2). Make sure that the end of the liner falls outside of
the printer.
Table 11 • Printer Parameters (Page 13 of 25)
Language/Parameter
Action/Explanation
1
2
- Z Series 1
- /RZ™ Series 1
- User Guide 1
- Part Number: 79695L-003 2
- Declaration of Conformity 3
- Compliance Information 4
- Contents 5
- Section Description 10
- T: Telephone 11
- F: Facsimile 11
- E: E-mail 11
- Document Conventions 12
- FEED button 13
- CANCEL button 13
- About This Document 14
- Introduction 15
- External View 16
- Printer Media Compartment 18
- Control Panel 19
- Control Panel Buttons 20
- Control Panel Lights 21
- Printer Language Modes 22
- Printer Setup 23
- Before You Begin 24
- Temperature Relative Humidity 25
- Select a Site for the Printer 26
- I) may damage the 27
- Interface 29
- Standard or 29
- Optional 29
- Description 29
- O) position 32
- Power Cord Specifications 33
- Types of Media 34
- Ribbon Overview 36
- If the ribbon... Then 37
- Operations 39
- Print Mode Printer Option 41
- Load Media 43
- Roll Media 44
- Fanfold Media 44
- Roll Media (Continued) 45
- Fanfold Media (Continued) 45
- PAUSE to enable printing 47
- Close the printhead assembly 57
- Ribbon Coated Outside 58
- (black ribbon spindle) 58
- Ribbon Coated Inside 58
- (gray ribbon spindle) 58
- Load Ribbon 59
- Remove Used Ribbon 62
- Calibrate the Printer 63
- Media Width 64
- If the media... Then 65
- Adjust Printhead Pressure 66
- Configuration 67
- Setup Mode 68
- Exit Setup Mode 69
- Default Password Value 70
- SETUP/EXIT 71
- LIST SETUP 71
- PLUS (+) to confirm printing 71
- LIST NETWORK 72
- Language/Parameter 73
- To change the value shown: 73
- Action/Explanation 74
- WARNING REPLACE 80
- To format a memory card: 83
- To initialize Flash memory: 84
- To print a sensor profile: 84
- LOAD BACKING prompt displays 85
- RELOAD ALL displays 86
- To skip these parameters: 94
- IDLE DISPLAY 96
- Replacing Printer Components 100
- Lubrication 100
- Area Method Interval 101
- Routine Maintenance 102
- Cleaning Procedures 102
- Clean the Cutter Module 106
- I) the printer 107
- Troubleshooting 111
- Troubleshooting Checklists 112
- LCD Error Messages 113
- O) the printer 114
- HEAD COLD 115
- HEAD TOO HOT 115
- DEFRAGMENTING 116
- ERROR CONDITION 116
- CUTTER JAM 116
- OUT OF MEMORY 116
- (function) 116
- Print Quality Problems 117
- Note • A vertical drift of 119
- Calibration Problems 120
- NONE. See 121
- Ribbon Problems 122
- RFID Problems 123
- MEDIA POWER UP and 125
- LANGUAGE 126
- SAVE CHANGES in the 126
- O) and then on (I) 127
- CANCEL self tests 129
- CANCEL Self Test 130
- PAUSE Self Test 131
- FEED Self Test 132
- Print Quality Description 133
- FEED and PAUSE Self Test 135
- Printer Diagnostics 136
- RIBBON (2). If 137
- MEDIA (3) for the media 137
- Specifications 139
- General Specifications 140
- Printing Specifications 141
- Media Specifications 143
- Ribbon Specifications 144
- Printer Options 145
- 1/11/11 Z Series 147
- 79695L-003 Z Series 148
Produits connexes et manuels pour Imprimer et scanner Zebra RZ Series
Imprimer et scanner Zebra TTPM2 Spécifications
(140 pages)
(140 pages)
(86 pages)
Imprimer et scanner Zebra CPCL Spécifications
(497 pages)
(497 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels