Zebra Z6Mplus Guide de l'utilisateur Page 138
- Page / 166
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Troubleshooting
Printer Diagnostics
130
13163L-001 Rev. A Z4Mplus/Z6Mplus User Guide 1/18/06
Figure 40 • Bar Code Darkness Comparison
Table 17 • Judging Bar Code Quality
Print Quality Description
Too dark Labels that are too dark are fairly obvious. They may be
readable but not “in-spec.”
• The normal bar code bars increase in size.
• The openings in small alphanumeric characters may fill in
with ink.
• Rotated bar code bars and spaces run together.
Slightly dark Slightly dark labels are not as obvious.
• The normal bar code will be “in-spec.”
• Small character alpha numerics will be bold and could be
slightly filled in.
• The rotated bar code spaces are small when compared to
the “in-spec” code, possibly making the code unreadable.
- Z4Mplus/Z6Mplus 1
- User Guide 1
- Declaration of Conformity 3
- Compliance Information 4
- Contents 5
- Who Should Use This Document 10
- Contacts 11
- Document Conventions 12
- FEED button 13
- CANCEL button 13
- About This Document 14
- Introduction 15
- External View 16
- Control Panel 17
- Control Panel Buttons 18
- Control Panel Lights 19
- Printer Media Compartment 20
- Printer Setup 21
- Before You Begin 22
- Handling the Printer 23
- Select a Site for the Printer 24
- Power Cord Specifications 26
- Connector Locations 27
- Types of Connections 28
- Data Cable Requirements 30
- Types of Media 31
- Ribbon Overview 33
- Adhesive Test 34
- Ribbon Scratch Test 34
- Operations 35
- Media Loading Overview 36
- Insert Media into the Printer 37
- Fanfold Media 38
- Load Media in Tear-Off Mode 39
- Slide out the media guide 40
- PAUSE to enable printing 41
- 5. Slide out the media guide 43
- Load Media in Cutter Mode 48
- Close the printhead assembly 51
- Load Media in Rewind Mode 52
- To operate in... Then 55
- Load Ribbon 61
- Remove Used Ribbon 64
- Calibrate the Printer 66
- Position the Media Sensors 67
- If you are using… Then… 68
- Adjust the Reflective Sensor 69
- Adjust Printhead Pressure 71
- Inside Dial Outside Dial 72
- Install Memory Card 73
- Configuration 75
- Setup Mode 76
- Exit Setup Mode 77
- Default Password Value 78
- Print a Configuration Label 79
- LIST NETWORK 80
- Control Panel LCD Displays 81
- PRINT SPEED 82
- 2 IPS + 82
- TEAR OFF +000 82
- SENSOR SELECT 84
- -AUTO SELECT + 84
- PRINT METHOD 84
- -THERMAL-TRANS. + 84
- PRINT WIDTH 85
- - 104 0/8 MM + 85
- MAXIMUM LENGTH 86
- -39.0 IN 988 MM 86
- To format a memory card: 89
- To initialize Flash memory: 90
- SENSOR PROFILE 91
- PRINT 91
- COMMUNICATIONS 96
- - NORMAL MODE + 96
- CONTROL PREFIX 96
- - < >7EH + 96
- FORMAT PREFIX 97
- - <^>5EH + 97
- DELIMITER CHAR 97
- - <,>2CH + 97
- ZPL MODE 98
- - ZPL II + 98
- MEDIA POWER UP 98
- - CALIBRATION + 98
- HEAD CLOSE 99
- BACKFEED 99
- - DEFAULT + 99
- LABEL TOP +000 100
- - + 100
- LEFT POSITION 100
- - ±0000 + 100
- Parameter 101
- To skip these parameters: 101
- To change the value shown: 101
- LANGUAGE 103
- Print Server LCD Displays 104
- ENCRYPTION MODE 107
- ENCRYPT. INDEX 107
- Routine Maintenance 109
- Lubrication 110
- Cleaning Procedures 110
- Clean the Rewind Option 114
- Clean the Peel-Off Assembly 115
- Close the media door 117
- Clean the Cutter Module 118
- Replace the cutter shield 119
- Fuse Replacement 120
- Troubleshooting 121
- Troubleshooting Checklists 122
- LCD Error Messages 123
- LCD Display/ 124
- Printer Condition 124
- Caution • Turn off (O) the 125
- O) the printer 125
- I) the printer 125
- Print Quality Problems 126
- Note • A vertical drift of 128
- Calibration Problems 129
- Communications Problems 130
- SAVE CHANGES in the 131
- Calibrate 132
- Printer Diagnostics 133
- CANCEL Self Test 134
- PAUSE Self Test 135
- FEED Self Test 136
- Print Quality Description 138
- FEED and PAUSE Self Test 140
- Data Ports 141
- Parallel Data Port 142
- 36-Pin Connectors 143
- Serial Data Port 144
- Pin Configuration 145
- RS-232 Interface Connections 146
- Modem Connection 147
- Specifications 149
- General Specifications 150
- Agency Approvals 151
- Printing Specifications 152
- Media Specifications 153
- Ribbon Specifications 155
- Printer Options 156
- ZPL II Features 157
- Supported Bar Codes 157
- Cutter Jam message, 117 160
- HEAD COLD message, 117 160
- HEAD TOO HOT message, 116 160
- OUT OF MEMORY message, 117 162
- PAPER OUT message, 116 162
- RIBBON IN message, 116 163
- RIBBON OUT message, 115 163
- © 2006 ZIH Corp 166
Produits connexes et manuels pour Imprimantes d'étiquettes Zebra Z6Mplus
(106 pages)
(20 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels