Zebra MZ series Manuel d'utilisateur Page 2
- Page / 44
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
RMAN-MZS-002 • -ii •
Proprietary Statement
This manual contains proprietary information of Zebra Technologies Corporation and its subsidiaries (“Zebra Tech-
nologies”). It is intended solely for the information and use of parties operating and maintaining the equipment de-
scribed herein. Such propriety information may not be used, reproduced, or disclosed to any other parties for any
other purpose without the expressed written permission of Zebra Technologies.
Product Improvements
Continuous improvement of products is a policy of Zebra Technologies. All specifications and designs are subject
to change without notice.
FCC Compliance Statement
Digital apparatus has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the product manuals, may cause harmful inter-
ference to radio communications. Operation of this equipment in a residential area is likely to cause harmful inter-
ference in which case the user will be required to correct the interference at his own expense.
The user is cautioned that any changes or modifications not expressly approved by Zebra Technologies could void
the user’s authority to operate the equipment. This unit was tested with shielded cables on the peripheral devices.
Shielded cables must be used with the unit to insure compliance.
WARNING: EXPOSURE TO RADIO FREQUENCY RADIATION ON SOME MODELS. TO CONFORM TO FCC RF
EXPOSURE REQUIREMENTS THIS DEVICE SHALL BE USED IN ACCORDANCE WITH THE OPERATING CONDI-
TIONS AND INSTRUCTIONS LISTED IN THIS UNIT’S USER’S MANUAL.
Canadian DOC Compliance Statement
Digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in
the radio interference regulations of the Canadian Department of Communications.
Liability Disclaimer
Zebra Technologies takes steps to assure that its published Engineering specifications and manuals are correct;
however, errors do occur. Zebra Technologies reserves the right to correct any such errors and disclaims liability
resulting therefrom.
Limitation of Liability
In no event shall Zebra Technologies or anyone else involved in the creation, production or delivery of the ac-
companying product (including hardware and software) be liable for any damages whatsoever (including, without
limitation, consequential damages including loss of business profits, business interruption or loss of business infor-
mation) arising out of the use of or the results of use of or inability to use such product, even if Zebra Technologies
has been advised of the possibility of such damages. Some jurisdictions do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may not apply to you.
Copyrights
The copyrights in this manual and the label printer described therein are owned by Zebra Technologies. All rights
are reserved. Unauthorized reproduction of this manual or the software in the label printer may result in imprison-
ment of up to one year and fines of up to $10,000 (17 U.S.C.506). Copyright violators may be subject to civil liability.
©2007 ZIH Corp. All trademarks and registered trademarks are property of their respective owners. All rights re-
served.
- MZ Series 1
- RMAN-MZS-002 • -ii • 2
- CONTENTS 3
- Description 4
- Printing Technology 4
- Communications 4
- User Guide 4
- DIAGNOSTIC TOOLS 5
- Diagnostic Label Printout 5
- Label Vista™ 5
- Factory Technical Support 6
- LABEL VISTA™ 6
- INTRODUCTION TO LABEL VISTA 7
- Starting Label Vista 7
- Equipment Required 8
- Running The Software 8
- Handling: 9
- STORAGE AND HANDLING 9
- TOOLS AND SUPPLIES 9
- Install the Replacement Cover 11
- Optional step for MZ 320: 13
- Install the Upper Housing 14
- Long Self-Tapping 16
- Screw (2) 16
- Short Self-Tapping 16
- Upper Housing 16
- Battery Compartment Cover 17
- Battery Compartment Lock 17
- Belt Clip 17
- Door, Rubber 19
- Insert into slot in Lower 19
- Housing. Use flat bladed 19
- CF18427-1 19
- Antenna 20
- Coax Cable 20
- Replace the Printer Frame 21
- Assemble The Printer Frame 24
- Replace the Motor 26
- Remove the Gears 26
- Install the Replacement Gears 26
- Remove the Motor 29
- Remove the Radio Board 32
- • Coin or tool p/n CF18330-1 34
- Install the Battery 35
- REPAIR KITS 36
- North America, Aust. NZ 37
- EU/EFTA, India, Russia 37
- Argentina, Brazil 37
- PCC Example 38
- PCC Bar 39
- MZ SERIES ACCESSORIES 40
- MZ SERIES REPLACEMENT KITS 41
Produits connexes et manuels pour Imprimer et scanner Zebra MZ series
(20 pages)
Imprimer et scanner Zebra Z6M Spécifications
(168 pages)
(168 pages)
Imprimer et scanner Zebra TTP7030 Spécifications
(144 pages)
(144 pages)
Imprimer et scanner Zebra EPL2 Spécifications
(154 pages)
(154 pages)
Horizon Fitness E6 manuály
Uživatelské manuály a uživatelské příručky pro Fitness, gymnastika a silový trénink Horizon Fitness E6.
Poskytujeme 1 manuály pdf Horizon Fitness E6 ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Commentaires sur ces manuels