Zebra ZE500 Guide de l'utilisateur Page 59
- Page / 170
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
59
Printer Setup and Operation
Connect the Print Engine to a Power Source
8/23/12 P1051584-002
Connect the Print Engine to a Power Source
The AC power cord must have a three-prong female connector on one end that plugs into the
mating AC power connector at the rear of the print engine. If a power cable was not included
with your print engine, refer to
Power Cord Specifications on page 60.
To connect the print engine to a power source, complete these steps:
1. Plug the female end of the A/C power cord into the A/C power connector on the back of
the print engine.
2. Plug the male end of the A/C power cord into an appropriate power outlet.
Caution • For personnel and equipment safety, always use an approved three-conductor
power cord specific to the region or country intended for installation. This cord must use an
IEC 320 female connector and the appropriate region-specific three-conductor grounded
plug configuration.
115 V AC
230 V AC
- User Guide 1
- DECLARATION OF CONFORMITY 3
- Compliance Information 4
- Contents 5
- About This Document 9
- Who Should Use This Document 10
- Contacts 11
- Document Conventions 12
- Introduction 13
- Print Engine Orientation 14
- Print Engine Components 15
- POWER PAUSE STATUS DATA 16
- Default Password Value 20
- Control Panel Display 21
- • the non-resettable counter 26
- 3. Do you want to continue? 28
- PERMANENT 36
- Types of Media 39
- Printer Setup and Operation 40
- Ribbon Overview 41
- Adhesive Test 42
- Ribbon Scratch Test 42
- Printer Setup and 43
- Operation 43
- Handling the Print Engine 44
- Remove the metal spacer 46
- To Store the Print Engine 47
- To Ship the Print Engine 47
- Print Engine Installation 48
- 9.648 in 50
- (245 ± 0.1 mm) 50
- 0.445 in 50
- (11.3 mm) 50
- 16.62 in. (422.1 mm) 51
- Data Cables 58
- 115 V AC 59
- 230 V AC 59
- Power Cord Specifications 60
- Load Ribbon and Media 62
- Loading Media 65
- 19. Close the media door 69
- Printer Configuration 71
- Adjustment 71
- Changing Printer Settings 72
- Print Settings 73
- Applicator 75
- • ZE500-4 203 dpi: 832 dots 77
- • ZE500-4 300 dpi: 1228 dots 77
- • ZE500-6 203 dpi: 1344 dots 77
- • ZE500-6 300 dpi: 1984 dots 77
- ~JS when received 79
- • ENABLED 80
- • DISABLED 80
- Directory Listing 88
- Network Settings 89
- Print Server Settings > 92
- Print Server Settings 92
- Language Settings 93
- • ZPL II 94
- Sensor Settings 95
- Port Settings 96
- ZEBRA response messages are 98
- ZEBRA is selected, the print 98
- DSR/DTR for host 98
- LOAD BACKING 99
- P1051584-002 8/23/12 100
- REMOVE RIBBON 101
- CALIBRATING 101
- PLEASE WAIT 101
- RELOAD ALL 101
- Close the media door 102
- Remove Used Ribbon 103
- Adjust the Sensors 104
- Reflective Media Sensor 105
- Ribbon Sensor 105
- Toggle Positioning 106
- I) the printer.) 107
- Printhead Pressure Adjustment 108
- Routine Maintenance 111
- CLEAN HEAD NOW appears 112
- Clean the Media Compartment 113
- 7. Close the media door 114
- Lubrication 115
- Troubleshooting 117
- Printing Issues 118
- Ribbon Problems 121
- Error Messages 122
- 1) is likely 123
- O) the print engine 124
- I) the print engine 124
- Display/ 126
- Print Engine Condition 126
- Communications Problems 127
- Miscellaneous Issues 128
- Print Engine Diagnostics 130
- CANCEL Self Test 131
- PAUSE Self Test 132
- FEED Self Test 133
- Print Quality Description 134
- FEED + PAUSE Self Test 136
- CANCEL + PAUSE Self Test 136
- FE indicates a framing error 137
- PE indicates a parity error 137
- NE indicates noise 137
- Sensor Profile 138
- MEDIA (3) for the media 139
- Specifications 141
- General Specifications 142
- Printing Specifications 143
- Ribbon Specifications 143
- Media Specifications 144
- Applicator Interface Board 145
- Reconfiguration 145
- Remove Power and Data Cables 146
- ) off of the print engine 147
- 8/23/12 P1051584-002 149
- The installation is complete 155
- Glossary 157
- 8/23/12 P1051584-002 161
Produits connexes et manuels pour Imprimer et scanner Zebra ZE500
Imprimer et scanner Zebra EPL2 Spécifications
(138 pages)
(138 pages)
(76 pages)
(64 pages)
(27 pages)
Imprimer et scanner Zebra TTPM3 Spécifications
(112 pages)
(112 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.086 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels