Zebra 105SL Plus Guide de l'utilisateur Page 113
- Page / 174
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
105
PC and Memory Cards
PCMCIA PC Cards
6/30/06 105SL User Guide 11342L-001 Rev. A
2. Insert the PCMCIA card into the card slot with the notch up. Insert it far enough to make
the card-eject button pop out.
3. Reinstall the card shield over the PCMCIA card and card slot.
The printer is ready to operate with the additional memory, font option, or wireless
capability. To be sure that a memory or font card has successfully initialized, print a
configuration label as instructed in Print a Configuration Label on page 77, and review it
to see if the new card information is listed. For wireless cards, follow the instructions in
Print a Network Configuration Label on page 78.
Note • The PCMCIA card may take a few minutes to initialize. The PAUSE light flashes
while the card initializes. If the card is already initialized, the
PAUSE light flashes only
once or twice after the card is installed.
- User Guide 1
- Declaration of Conformity 3
- Compliance Information 4
- Contents 5
- Who Should Use This Document 10
- Contacts 11
- Document Conventions 12
- SETUP/EXIT button 13
- About This Document 14
- Introduction 15
- External View 16
- Control Panel 17
- Control Panel LCD 18
- Control Panel Buttons 18
- Control Panel Lights 19
- Printer Media Compartment 21
- Printer Setup 23
- Before You Begin 24
- Handling the Printer 25
- Select a Site for the Printer 26
- Connector Locations 27
- Types of Connections 28
- Data Cable Requirements 30
- 4. Turn on (I) the printer 31
- Power Cord Specifications 32
- Types of Media 33
- Ribbon Overview 35
- Adhesive Test 36
- Ribbon Scratch Test 36
- Operations 37
- Media Loading Overview 38
- Insert Media into the Printer 39
- Fanfold Media 40
- If… Then… 41
- Load Media in Tear-Off Mode 42
- Load Media in Peel-Off Mode 46
- If the printer has 47
- 1). Insert the long end 51
- If... Then 55
- Pull out the spindle hook 56
- Load Media in Rewind Mode 57
- 1) and the adjustable hook 58
- 2) point down 58
- Load Media in Cutter Mode 65
- Load Ribbon 69
- Remove Used Ribbon 73
- Adjust Media Sensors 74
- Lower Media Sensor 75
- Adjust Printhead Balance 76
- Printhead Pressure Adjustment 78
- Calibrate the Printer 79
- Setup Mode 82
- Exit Setup Mode 83
- Default Password Value 84
- Print a Configuration Label 85
- LIST NETWORK 86
- TEAR OFF +000 88
- - + 88
- PRINT MODE 88
- -TEAR-OFF + 88
- Action/Explanation 89
- PRINT WIDTH 90
- - MM + 90
- MAXIMUM LENGTH 91
- -39.0 IN 988 MM 91
- To format a memory card: 93
- To initialize Flash memory: 94
- SENSOR PROFILE 95
- PRINT 95
- To change the value shown: 100
- Parameter 100
- LEFT POSITION 102
- - ±0000 + 102
- HEAD RESISTOR 103
- - 0500 OHMS + 103
- To skip these parameters: 104
- Print Server LCD Displays 106
- ^WE ZPL command to set 108
- PLUS (+) to select YES 109
- Parameter Action/Explanation 109
- Configuration 110
- Control Panel Parameters 110
- PC and Memory Cards 111
- PCMCIA PC Cards 112
- PAUSE light flashes 113
- PAUSE light flashes only 113
- Routine Maintenance 115
- Lubrication 116
- Cleaning Schedule 116
- Clean the Exterior 117
- Take-label sensors 121
- Black mark sensor 121
- Ribbon sensor 121
- Clean the Snap Plate 122
- Clean the Cutter 123
- Replace the Fuse 124
- Troubleshooting 125
- Troubleshooting Checklists 126
- LCD Error Messages 127
- LCD Display/ 128
- Printer Condition 128
- HEAD COLD 129
- OUT OF MEMORY 129
- (function) 129
- Print Quality Problems 130
- Note • A vertical drift of 132
- Calibration Problems 133
- Communications Problems 134
- Ribbon Problems 135
- LANGUAGE 136
- SAVE CHANGES in the 136
- Calibrate 137
- Printer Diagnostics 138
- CANCEL Self Test 139
- PAUSE Self Test 141
- FEED Self Test 142
- Print Quality Description 144
- FEED and PAUSE Self Test 146
- Sensor Profile 148
- Specifications 149
- General Specifications 150
- Communications Specifications 151
- Other Standard Features 151
- Additional Options 151
- Agency Approvals 152
- Printing Specifications 153
- Ribbon Specifications 153
- Media Specifications 154
- Bar Codes 155
- Glossary 157
- End User License 161
- Agreement 161
- End User License Agreement 162
- HEAD COLD message, 121 168
- HEAD TOO HOT message, 120 168
- OUT OF MEMORY message, 121 169
- PAPER OUT message, 120 170
- RIBBON IN message, 120 171
- RIBBON OUT message, 119 171
- © 2006 ZIH Corp 174
Produits connexes et manuels pour Imprimer et scanner Zebra 105SL Plus
Imprimer et scanner Zebra TTP2130 Spécifications
(138 pages)
(138 pages)
Imprimer et scanner Zebra EPL2 Spécifications
(138 pages)
(138 pages)
(76 pages)
(64 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels