Zebra ZD500 Guide de l'utilisateur Page 128
- Page / 160
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Maintenance
RTC Battery
116
P1062653-002 Rev. A ZD500 Series™ Thermal Transfer Printer User’s Guide 1/16/2014
7. Align the platen with the gear to the left and lower it into the printer’s bottom frame.
8. Rotate the platen bearing latch release tabs down on the right and left sides towards the
rear of the printer and snap them into place.
Allow the printer to dry for one minute before closing the dispenser door, media cover or
loading labels.
Other Printer Maintenance
There are no user level maintenance procedures beyond those detailed in this section. See the
Troubleshooting on page 123 for more information on diagnosing printer and print problems.
RTC Battery
The RTC (Real-Time Clock) battery is not operator replaceable. See a Zebra authorized
service technician to replace the battery.
Fuses
There are no replaceable fuses in the ZD500 Series™ printer or power supply.
Caution • The printer has a three volt lithium battery. You can discern a low or flat battery if
the printer provides a consistently delayed date stamp. Battery replacement must be performed
by a qualified service technician. Only use a Zebra approved replacement battery.
Important • Recycle batteries according to local your guidelines and regulations. Wrap the
battery when disposing (or storing) to avoid a short circuit.
DO NOT short circuit the battery. Short circuiting the battery may result in heat
generation, fire or bursting.
DO NOT heat, disassemble or dispose of battery in fire.
- ZD500 Series™ 1
- Mexico — NOM-121-SCT1-2009 3
- Industry Canada (IC) Warning 4
- Brasil — Aviso da Anatel 4
- Japan Restricted Frequencies 4
- Taiwan Restricted Frequencies 5
- Korean Compliance Statement 5
- RFID Radio Specification 7
- WLAN Radio Specification 7
- Bluetooth 2.1 + EDR 7
- Environmental Management 8
- Document Conventions 8
- Contents 10
- Introduction 13
- What’s in the Box? 16
- Printer Features 17
- Media Cutter 19
- (Option) 19
- enters the menu system 20
- accepts the values shown 20
- Control Panel 21
- Figure 5 • Typical Home Menu 22
- Printer Control Panel Display 23
- ) button 24
- ) button or press RIGHT 25
- Control Panel Menu Map 26
- (software/driver) setup 27
- Attaching Power 29
- Preparing and Handling Media 30
- Loading Roll Media 32
- Loading Transfer Ribbon 35
- Pre-install Windows 40
- Printer Drivers 40
- Interface Cable Requirements 40
- USB Interface 41
- Parallel Interface 41
- Serial Interface 42
- Ethernet Cable 44
- (RJ45 Connector) 44
- Green LED Amber LED 44
- Wireless and then click Next 47
- If you select… Then… 50
- Click Next 52
- Tabletop/Desktop 52
- O) and then back on (I) 53
- Status Indicator Meaning 54
- Connecting to a Windows XP 57
- SP2 Master Device 57
- Connecting to a Windows Vista 57
- SP2 or Windows 7 57
- Master Device 57
- Printer Configuration 63
- SETTINGS Menu 64
- Changing Printer Settings 65
- TOOLS Menu 68
- Directory Listing 72
- NETWORK Menu 73
- RFID Menu 77
- LANGUAGE Menu 81
- • ZPL II 82
- SENSOR Menu 83
- PORTS Menu 84
- "bidirectional" 85
- "unidirectional" 85
- BLUETOOTH Menu 86
- ) button 87
- Thermal Printing 90
- Modes of Printing 90
- Types of Media 91
- Media Loading 93
- Ribbon Overview 96
- Ribbon Scratch Test 97
- Replacing Supplies 98
- Adjusting the Print Width 99
- Adjusting the Print Quality 99
- Media Sensing 100
- Print Operations 101
- Black Marks 102
- Default Gap 104
- Sensing Position 104
- DefaultCenter Aligned 104
- Printing on Fan-Fold Media 105
- 5. Close the top cover 106
- Sending Files to the Printer 107
- Fonts and Your Printer 108
- Getting Asian Fonts 109
- Printer Options 111
- Label Dispenser Option 112
- 4. Close the dispenser door 114
- Cutter Option 115
- Under Media 117
- ZebraNet 118
- Bluetooth Option 119
- Maintenance 121
- Cleaning 122
- Cleaning the Printhead 123
- Media Path Cleaning 124
- Sensor Cleaning 125
- Platen Bearings 126
- RTC Battery 128
- Replacing the Printhead 129
- Troubleshooting 135
- Error Messages 136
- Printing Issues 138
- Ribbon Problems 141
- Communications Problems 142
- Miscellaneous Issues 143
- RFID Troubleshooting 144
- Printer Diagnostics 145
- Configuration Report 146
- Print Quality Report 147
- Print Quality Description 148
- O) the printer 150
- I) the printer 150
- FE indicates a framing error 151
- PE indicates a parity error 151
- NE indicates noise 151
- Sensor Profile 152
- Appendix: Interface Wiring 155
- Serial Port Interface 156
- Appendix: Dimensions 157
- Label Dispenser 159
Produits connexes et manuels pour Imprimantes d'étiquettes Zebra ZD500
(18 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.071 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels