Zebra ZD500 Guide de l'utilisateur Page 64
- Page / 160
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Printer Configuration
Changing Printer Settings
52
P1062653-002 Rev. A ZD500 Series™ Thermal Transfer Printer User’s Guide 1/16/2014
SETTINGS Menu
Table 7 • SETTINGS Menu
Print
Darkness
Set the darkness to the lowest setting that provides good print quality. If you set the darkness
too high, the label image may print unclearly, bar codes may not scan correctly, the ribbon
may burn through, or the printhead may wear prematurely.
If desired, use the Print Quality Report on page 135 to determine the best darkness setting.
Accepted values:
0.0 – 30.0
Related ZPL command(s):
^MD, ~SD
SGD command used:
print.tone
Printer web page:
View and Modify Printer Settings > General Setup >
Darkness
Print Speed Select the speed for printing a label (given in inches per second). Slower print speeds
typically yield better print quality.
Accepted values:
2, 3, 4, 5, 6
Related ZPL command(s):
^PR
SGD command used:
media.speed
Printer web page: N/A
Media Type Select the type of media that you are using.
• If you select CONTINUOUS, you must include a label length in your label format (^LL
if you are using ZPL).
• If you select GAP/NOTCH or MARK for various non-continuous media, the printer
feeds media to calculate the label length.
See Types of Media on page 79 for more information.
Accepted values:
• CONTINUOUS
• GAP/NOTCH
• MARK
Related ZPL command(s):
^MN
SGD command used:
ezpl.media_type
Printer web page:
View and Modify Printer Settings > Media Setup >
Media Type
Print Method Specify if the printer is to use Direct Thermal mode (no ribbon) or Thermal Transfer mode
(using thermal transfer media and ribbon).
Accepted values:
• THERMAL TRANS
• DIRECT THERMAL
Related ZPL command(s):
^MT
SGD command used:
ezpl.print_method
Printer web page:
View and Modify Printer Settings > Media Setup >
Print Method
- ZD500 Series™ 1
- Mexico — NOM-121-SCT1-2009 3
- Industry Canada (IC) Warning 4
- Brasil — Aviso da Anatel 4
- Japan Restricted Frequencies 4
- Taiwan Restricted Frequencies 5
- Korean Compliance Statement 5
- RFID Radio Specification 7
- WLAN Radio Specification 7
- Bluetooth 2.1 + EDR 7
- Environmental Management 8
- Document Conventions 8
- Contents 10
- Introduction 13
- What’s in the Box? 16
- Printer Features 17
- Media Cutter 19
- (Option) 19
- enters the menu system 20
- accepts the values shown 20
- Control Panel 21
- Figure 5 • Typical Home Menu 22
- Printer Control Panel Display 23
- ) button 24
- ) button or press RIGHT 25
- Control Panel Menu Map 26
- (software/driver) setup 27
- Attaching Power 29
- Preparing and Handling Media 30
- Loading Roll Media 32
- Loading Transfer Ribbon 35
- Pre-install Windows 40
- Printer Drivers 40
- Interface Cable Requirements 40
- USB Interface 41
- Parallel Interface 41
- Serial Interface 42
- Ethernet Cable 44
- (RJ45 Connector) 44
- Green LED Amber LED 44
- Wireless and then click Next 47
- If you select… Then… 50
- Click Next 52
- Tabletop/Desktop 52
- O) and then back on (I) 53
- Status Indicator Meaning 54
- Connecting to a Windows XP 57
- SP2 Master Device 57
- Connecting to a Windows Vista 57
- SP2 or Windows 7 57
- Master Device 57
- Printer Configuration 63
- SETTINGS Menu 64
- Changing Printer Settings 65
- TOOLS Menu 68
- Directory Listing 72
- NETWORK Menu 73
- RFID Menu 77
- LANGUAGE Menu 81
- • ZPL II 82
- SENSOR Menu 83
- PORTS Menu 84
- "bidirectional" 85
- "unidirectional" 85
- BLUETOOTH Menu 86
- ) button 87
- Thermal Printing 90
- Modes of Printing 90
- Types of Media 91
- Media Loading 93
- Ribbon Overview 96
- Ribbon Scratch Test 97
- Replacing Supplies 98
- Adjusting the Print Width 99
- Adjusting the Print Quality 99
- Media Sensing 100
- Print Operations 101
- Black Marks 102
- Default Gap 104
- Sensing Position 104
- DefaultCenter Aligned 104
- Printing on Fan-Fold Media 105
- 5. Close the top cover 106
- Sending Files to the Printer 107
- Fonts and Your Printer 108
- Getting Asian Fonts 109
- Printer Options 111
- Label Dispenser Option 112
- 4. Close the dispenser door 114
- Cutter Option 115
- Under Media 117
- ZebraNet 118
- Bluetooth Option 119
- Maintenance 121
- Cleaning 122
- Cleaning the Printhead 123
- Media Path Cleaning 124
- Sensor Cleaning 125
- Platen Bearings 126
- RTC Battery 128
- Replacing the Printhead 129
- Troubleshooting 135
- Error Messages 136
- Printing Issues 138
- Ribbon Problems 141
- Communications Problems 142
- Miscellaneous Issues 143
- RFID Troubleshooting 144
- Printer Diagnostics 145
- Configuration Report 146
- Print Quality Report 147
- Print Quality Description 148
- O) the printer 150
- I) the printer 150
- FE indicates a framing error 151
- PE indicates a parity error 151
- NE indicates noise 151
- Sensor Profile 152
- Appendix: Interface Wiring 155
- Serial Port Interface 156
- Appendix: Dimensions 157
- Label Dispenser 159
Produits connexes et manuels pour Imprimantes d'étiquettes Zebra ZD500
(18 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.065 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels