Zebra TTP2130 Spécifications Page 103
- Page / 138
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
103
Page Setup
Parameters Used
10/22/2008 TTP2100 Technical Manual P1003640-001
Parameters Used
Parameter n35 – Document Mode
Set parameter n36 to 1 to enable black-mark check.
Parameters n37 and n38 – Page Length Minimum
Measure the distance from the center of one black-mark to the center of the next. The
resolution is 0.125 mm so multiply the distance by 8, then calculate the value to enter as n37
and n38.
Parameter n39 – Max Black-markLength
Measure the height of the black-mark or gap. The resolution is 0.125 mm so multiply the
black-mark length (in millimeters) by 8 and enter the value as n39.
Parameter n40 – Min Black-mark Length (Garbage Filter)
This parameter is actually a filter to filter-out garbage on the paper. If a spot or perforation is
smaller than this value, it will not be regarded as a black-mark. 1. About ⅓ of the black-mark
length is usually a suitable setting.
n37+n38
n39
n40
Example • If the page length is 100mm,
(100 x 8) / 256 = 3.125.
n37 is the integer value, that is 3, while n38 is the fraction, 0.125 x 256 = 32
- Zebra® TTP2100 1
- Technical Manual 1
- Contents 3
- Introduction 7
- Contacts 8
- Product Presentation 10
- Print and drop 11
- Print and take 11
- Controls 12
- Description 13
- Installation 15
- Installing a Paper Guide 16
- 11. Press SET 17
- 12. Press STORE 17
- Value When Used 17
- 3. Tighten the screw 18
- Calibrating the TOF Sensor 19
- Installation Considerations 20
- Quick-Fit Hubs 21
- Push down 22
- Ambient Light 24
- Paper low 25
- Connector 25
- Connecting to the Computer 26
- TTP 2130 27
- Connecting the Power 29
- Oscilloscope Setting 2A/div 30
- Self-test 31
- Making a Test Printout 32
- Installing a Printer Driver 33
- Printer Features 35
- Black-mark Settings: 36
- Operation 37
- Loading Fanfold Ticket Stock 38
- Temperature-sensitive 39
- SW96074C 39
- Wrong! Wrong! Wrong! 40
- 1. Open the printer lid 41
- Clearing Paper Jams 42
- Programming 43
- Driver Oriented 44
- ESC ! n1 45
- Select font 45
- 1B 23 Hex 48
- 27 35 decimal 48
- 1B 5A Hex 48
- 27 90 Decimal 48
- Software command syntax 49
- Barcode Commands 53
- Name Dec Hex 55
- 1B 42 57 n1 nx Hex 56
- 027 066 087 n1 nx Decimal 56
- 1B 42 43 n1 hex 56
- 27 66 67 n1 decimal 56
- 1B 7C n1 nx Hex 57
- 027 124 n1 nx Decimal 57
- 1B 62 n1...n5 Data hex 58
- 27 98 n1...n5 Data decimal 58
- 1B 73 nDataHex 58
- 27 115 n Data Decimal 58
- 1B 72 n1...n9 hex 59
- 27 114 n1...n9 decimal 59
- 1B 67 n1...n5 hex 60
- 27 103 n1...n5 decimal 60
- 1B 4C n1 Hex 60
- 27 76 n1 Decimal 60
- Print Commands 61
- Cut and Present Commands 62
- System Related Commands 64
- 1B 26 73 0A hex 67
- 27 38115 10 decimal 67
- 1B 00 Hex 67
- 27 0 Decimal 67
- Status Code Meaning 68
- 1B 05 04 hex 70
- 27 5 4 decimal 70
- 1B 05 05 hex 70
- 27 5 5 decimal 70
- 1B 05 06 hex 71
- 27 5 6 decimal 71
- 2. The printer is printing 72
- 1B 05 0C hex 74
- 27 5 12 decimal 74
- 1B 05 63 hex 74
- 27 5 99 decimal 74
- 1B 05 45 hex 75
- 27 5 69 decimal 75
- 1B 05 50 n1 Hex 76
- 27 5 80 n1 Decimal 76
- 1B 06 n1 hex 76
- 27 6 n1 decimal 76
- Font Loading 77
- Character Bitmap Data 78
- Logotypes 79
- Printing 80
- Status Reporting 81
- Default Parameter Settings 83
- Default Value 84
- Examples 84
- Summary of Parameter Settings 85
- TTP model 86
- 2110 2130 86
- Serial Interface Set-up 87
- Print Setup 88
- Fixed Document Mode 91
- Cut Position Calibration 93
- Wall Compensation (mm) 93
- TOF Sensor Mask 97
- BM Sensor 97
- Printable Area 100
- Page Setup 101
- Simple Calibration Process 102
- Parameters Used 103
- FF (Form Feed) 106
- Interface 109
- Parameter Options 110
- USB, TTP 2130 111
- Maintenance 113
- Symptom Suggested actions 114
- 1. Open the printhead 115
- Firmware 116
- FW version Change 117
- Maintenance 118
- Specifications 119
- Ticket Specifications 120
- TOF Detection 120
- Print Module 121
- Ticket Separation 121
- Presenter 121
- Electronics 122
- Text Mode 122
- Basic Character Set 123
- Miscellaneous 124
- Ordering Number List 124
- Printer Shown on 125
- Dimensions 126
- Media Holder 127
- 70W Power Supply 128
- 150W Power Supply 129
- Part Number: P1003640-001 138
- © 2008 ZIH Corp 138
Produits connexes et manuels pour Imprimer et scanner Zebra TTP2130
Imprimer et scanner Zebra EPL2 Spécifications
(138 pages)
(138 pages)
(76 pages)
(64 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.097 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels