Zebra MP6000 Spécifications Page 94
- Page / 210
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
3 - 4 MP6000 INTEGRATOR GUIDE
Checkstand Preparation
If the MP6000 is not replacing an old bioptic device, and you are installing for the first time into a new
checkstand, verify that the area allows for proper cabling, and an AC/DC power supply. Mounting may require
installation of support(s), leveling screws, and peripheral devices. See Counter Cutout on page 3-5 for more
details about the location and preparation of the opening.
Figure 3-3
Preparing the Checkstand
Liquid Spills and Moisture
Select a checkstand design which allows fluids to flow through, and directs liquids and moisture build up away
from any electronic equipment or storage areas. Should a liquid spill occur, ensure that moisture can flow
through the checkstand without pooling. The power supply should be away from any area where spills may
occur.
Vertical Clearance
For all configurations of the MP6000, the maximum height above the platter is
5.1 in.;
the maximum depth
below the platter is
4.08 in.
Tools
No tools are required to install a MP6000 without a scale, or a Checkpoint antenna. The following tools are
required to mount the Scale Display:
•
Ruler (or similar measuring device)
•
Pencil (or similar measuring device)
•
Drill
•
2.4 mm (3/32 in.) diameter drill bit (to make screw holes where display is to be mounted)
•
19 mm (3/4 in.) diameter drill bit (to make cable pass through hole where display is to be mounted)
•
#2 Phillips screwdriver.
If the optional leveling screws are used on a
small or medium MP6000, a Phillips or flat blade screwdriver is
needed.
IMPORTANT The long (20.0 in./50.2 cm) versions are not available with leveling screws. The checkstand should
provide for two leveling screws under the front and rear of the MP6000. The medium (15.7 in./39.9
cm) and short (13.9 in./35.3 cm) MP6000 models have available accessory kits for standard and
long leveling screws.
- INTEGRATOR GUIDE 1
- Warranty 4
- Revision History 5
- Table A 6
- TABLE OF CONTENTS 9
- Table of Contents ix 11
- Table of Contents xi 13
- ABOUT THIS GUIDE 15
- Notational Conventions 16
- Related Publications 16
- About This Guide vii 17
- FEATURES 19
- Product Overview 20
- Configurations 21
- 1 - 4 MP6000 INTEGRATOR GUIDE 22
- Table 1-1 23
- 1 - 6 MP6000 INTEGRATOR GUIDE 24
- Peripherals 26
- Features of the MP6000 27
- Left Side View 28
- View Under Platter 29
- Leveling Screws 29
- Figure 1-6 30
- Features Summary 31
- 2 - 2 MP6000 INTEGRATOR GUIDE 36
- Programming Management Tools 37
- Connecting a USB Interface 38
- USB Host Parameters 40
- * IBM Table-top USB 41
- USB Device Type (continued) 42
- Figure 2-3 47
- Table 2-3 47
- (see parameter 47
- page 2-32 47
- Connect MP6000 to RS-232 Host 48
- RS-232 Parameters 49
- RS-232 Host Parameters 50
- Table 2-7 52
- Table 2-8 53
- RS-232 Host Types 54
- *Standard RS-232 55
- RS-232 Host Types (continued) 56
- RS-232 Host -NCR Variant 64
- Parameter # 1246 66
- Third Party Scale 71
- Parameter # 1294 71
- Third Party Scale (continued) 72
- Third Party Scale LED Pin 73
- Parameter # 1295 73
- *Active High 74
- Third Party Scale Zero Pin 75
- Parameter # 1296 75
- IBM RS-485 Host Parameters 78
- *None Selected 79
- RS-232 AUX 1 87
- Scale Display Port 87
- RS-232 AUX 2 88
- Checkpoint Interlock 88
- AUX A-B (Stacked USB) 88
- Table 2-15 89
- Table 2-16 89
- INSTALLATION 91
- Site Preparation 92
- Grounding 93
- Liquid Spills and Moisture 94
- Vertical Clearance 94
- Counter Cutout 95
- Ergonomics 95
- Installing Components 96
- Unpacking MP6000 Equipment 97
- Pre-Installation Notes 98
- Required Tools 99
- Secure in Place 101
- Install the Scale Display 102
- Getting Started 104
- Installing 105
- Inserting the Scan Module 109
- Connecting the USB Cable 110
- Figure 3-25 112
- Figure 3-24 112
- Install the MP6000 /Scale 115
- Figure 3-30 116
- Figure 3-31 116
- Figure 3-32 117
- Figure 3-33 117
- Optional leveling screw kit 117
- MX301-SR00004ZZWR 117
- Figure 3-34 118
- Figure 3-35 118
- Figure 3-36 119
- Figure 3-37 119
- MX301-SR00004ZZWR or 119
- MX302-SR00004ZZWR 119
- Figure 3-38 120
- Figure 3-39 120
- 11.50 in 121
- 292.2 mm 121
- 20.0 in 121
- 506.9 mm 121
- Install Sensormatic Coils 124
- Install Checkpoint Antenna 127
- Figure 3-48 128
- Figure 3-49 128
- Installing the Mounting Frame 129
- WITH A SCALE ONLY) 131
- Scale Configurations 132
- Identifying Firmware Version 132
- Legal Scale Dampening Filter 134
- Step 4 - Calibration at LOAD 135
- 4 - 6 MP6000 INTEGRATOR GUIDE 136
- Calibration Success 137
- Calibration Failure 137
- Verification Test 138
- Table 4-5 139
- Table 4-4 139
- Audit Tallies 141
- * Kilograms 143
- Legal Scale Units (continued) 144
- Scale Display Configuration 145
- Parameter # 986 145
- Parameter # 996 147
- * Low Vibration Sensitivity 148
- Parameter # 996 (continued) 149
- Table 4-6 151
- Overview 155
- Controls and Indicators 156
- OPERATING THE SCANNER 5 - 3 157
- Volume/Tone Control Button 158
- Soft Reset Buttons 159
- Single Interval Range Scales 160
- Dual Interval Range Scales 160
- OPERATING THE SCANNER 5 - 7 161
- 5 - 8 MP6000 INTEGRATOR GUIDE 162
- Scan Windows 163
- Operating Modes 164
- Programming the MP6000 164
- USB Staging Flash Drive 165
- Flash DrivesFlash Drives 166
- Loading Cloning Files 167
- Scanning 169
- Weighing Items 170
- Supported EAS Controllers 171
- Sensormatic EAS Hard Tags 172
- OPERATING THE SCANNER 5 - 19 173
- Beeper and LED Conditions 174
- OPERATING THE SCANNER 5 - 21 175
- Table 5-1 176
- OPERATING THE SCANNER 5 - 23 177
- CHAPTER 6 123SCAN2 179
- Requirements 180
- APPENDIX A MAINTENANCE 181
- TROUBLESHOOTING, AND 181
- ERROR CODES 181
- Troubleshooting 182
- Troubleshooting Assistance 183
- A - 4 MP6000 INTEGRATOR GUIDE 184
- Table A-1 185
- Scale Warning Codes 186
- A - 8 MP6000 INTEGRATOR GUIDE 188
- Technical Specifications 189
- B - 2 MP6000 INTEGRATOR GUIDE 190
- Table B-1 191
- B - 4 MP6000 INTEGRATOR GUIDE 192
- APPENDIX C HOST INTERFACE 193
- CHARACTER SETS 193
- RS-232 Character Sets 194
- Table C-1 195
- C - 4 MP6000 INTEGRATOR GUIDE 196
- C - 6 MP6000 INTEGRATOR GUIDE 198
- Table D-1 199
- D - 2 MP6000 INTEGRATOR GUIDE 200
- APPENDIX E COMMUNICATION 201
- PROTOCOLS 201
- E - 2 MP6000 INTEGRATOR GUIDE 202
- Numerics 203
- Index - 3 205
- Tell Us What You Think 207
© 2020, manymanuals.fr. Tous droits réservés | 0.019 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels